|
|
| (344 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt) |
| Zeile 1: |
Zeile 1: |
| Alle Einstellungen von TLP sind zentral in der Konfigurationsdatei '''/etc/default/tlp''' zusammengefaßt. Bei Paketupdates wird die vom Benutzer angepaßte Datei von der Paketverwaltung nur nach Rückfrage überschrieben oder aber als '''/etc/default/tlp.dpkg-dist''' abgelegt.
| | [[Bild:warning.png]] Die Inhalte dieser Seite waren veraltet und wurden deshalb vom TLP Autor entfernt. |
|
| |
|
| == Parameter ==
| | Bitte die [https://linrunner.de/tlp/settings offizielle Dokumentation (englisch)] verwenden. |
| | |
| == Originaldatei ==
| |
| Die Datei '''/etc/default/tlp''' aus dem Installationspaket als Referenz.
| |
| | |
| # tlp - Parameters for power save<br/>
| |
| # Set to "1" to enable power save
| |
| TLP_ENABLE="1"
| |
|
| |
| # Seconds laptop mode has to to wait after the disk goes idle before doing a sync.
| |
| # Non-zero value enables, zero disables laptop mode.
| |
| DISK_IDLE_SECS_ON_AC=0
| |
| DISK_IDLE_SECS_ON_BAT=2
| |
|
| |
| # Dirty page values (timeouts in secs).
| |
| MAX_LOST_WORK_SECS_ON_AC=15
| |
| MAX_LOST_WORK_SECS_ON_BAT=15
| |
|
| |
| # Change CPU voltages aka "undervolting" - Kernel with PHC patch required
| |
| # Freq:voltage pairs are written to /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
| |
| # CAUTION: only use this, if you thoroughly understand what you are doing!
| |
| #PHC_CONTROLS="F:V F:V F:V F:V" <br/>
| |
| # Hard disk devices (separate with spaces)
| |
| DISK_DEVICES="sda"
| |
|
| |
| # Hard disk advanced power management level: 1(max saving)..254(off)
| |
| # Levels 1..127 spin down the disk.
| |
| DISK_APM_LEVEL_ON_AC=254
| |
| DISK_APM_LEVEL_ON_BAT=128 <br/>
| |
| # SATA Link Power: min_power/medium_power/max_performance
| |
| SATA_LINKPWR_ON_AC="max_performance"
| |
| SATA_LINKPWR_ON_BAT="min_power" <br/>
| |
| # Wifi power save mode for Intel 2200, 3945, 4965, 5100, 5300:
| |
| # 1(min saving)..5(max saving)
| |
| # (Kernel < 2.6.30 only)
| |
| WIFI_PWR_ON_AC=1
| |
| WIFI_PWR_ON_BAT=5
| |
|
| |
| # Disable wake on lan: Y/N
| |
| WOL_DISABLE=Y
| |
|
| |
| # Enable power save for Intel HDA, AC97 devices (timeout in secs).
| |
| # A value of 0 disables power save.
| |
| SOUND_POWER_SAVE=1
| |
| # Disable controller too: Y/N (HDA only)
| |
| SOUND_POWER_SAVE_CONTROLLER=Y
| |
|
| |
| # Set to 1 to power off optical drive in UltraBay (ThinkPads only)
| |
| # when running on battery.
| |
| # Drive can be powered on again by releasing (and reinserting) the
| |
| # eject lever or by pressing the disc eject button on newer models.
| |
| # Note: an UltraBay hard disk is never powered off
| |
| BAY_POWEROFF_ON_BAT=0
| |
|
| |
| # Set to 1 to enable usb autosuspend for all devices
| |
| # on system startup.
| |
| USB_AUTOSUSPEND=0
| |
|
| |
| # Devices from the following list are excluded from usb autosuspend
| |
| # (separate with spaces). Use lsusb to get the id's.
| |
| #USB_BLACKLIST="1111:2222 3333:4444" <br/>
| |
| # Devices to disable on startup: bluetooth/wifi/wwan
| |
| #DEVICES_TO_DISABLE_ON_STARTUP="bluetooth" <br/>
| |
| # Devices to disable on shutdown: bluetooth/wifi/wwan
| |
| # (workaround for devices that are blocking shutdown)
| |
| #DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan" <br/>
| |
|
| |
| # Battery charge thresholds (ThinkPad only, tp-smapi kernel module required)
| |
| # Charging starts when the remaining capacity falls below the START_CHARGE_TRESH
| |
| # value and stops when exceeding the STOP_CHARGE_TRESH value.
| |
| # Main battery (values in %)
| |
| #START_CHARGE_THRESH_BAT0=96
| |
| #STOP_CHARGE_THRESH_BAT0=100
| |
| # Ultrabay battery (values in %)
| |
| #START_CHARGE_THRESH_BAT1=96
| |
| #STOP_CHARGE_THRESH_BAT1=100
| |
Die Inhalte dieser Seite waren veraltet und wurden deshalb vom TLP Autor entfernt.
