Error Codes

Numerische Error Codes

Error code	Symptom	FRU or action, in sequence	Anmerkung
0175	Bad CRC1, stop POST task-The EEPROM checksum is not correct.	System board	siehe 0175:_Bad_CRC1
0176	System Security-The system has been tampered with.	Run BIOS Setup Utility, and save the current setting by pressing F10. System board.
0177	Bad SVP data, stop POST task-The checksum of the supervisor password in the EEPROM is not correct.	System board.
0182	Bad CRC2. Enter BIOS Setup and load Setup defaults.-The checksum of the CRS2 setting in the EEPROM is not correct.	Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10. System board.
0185	Bad startup sequence settings. Enter BIOS Setup and load Setup defaults.	Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10.
0187	EAIA data access error-The access to EEPROM is failed.	System board.
0188	Invalid RFID Serialization Information Area.	System board.
0189	Invalid RFID configuration information area-The EEPROM checksum is not correct.	System board.
0190	Critical low-battery error.	Charge the battery pack. Battery pack.
0191	System Security-Invalid Remote Change requested.	Run BIOS Setup Utility, and then save current setting by pressing F10. System board.
0192	System Security- Embedded Security hardware tamper detected.	System board.
0199	System Security-Security password retry count exceeded.	Run BIOS Setup Utility, and then save the current setting by pressing F10. System board.
01C8	Two or more modem devices are found. Remove all but one of them. Press ESC to continue.	Remove either a Mini-PCI Card or a modem daughter card. Otherwise, press ESC to ignore the warning message. System board.
01C9	More than one Ethernet devices are found. Remove one of them. Press ESC to continue.	Remove the Ethernet device that you installed; or press ESC to ignore the warning message. System board.	1802 Error
01CA	More than one Wireless LAN devices are found. Remove one of them.	Remove the wireless LAN device that you installed. System board.
0200	Hard disk error-The hard disk is not working.	Reseat the hard disk drive. Load Setup Defaults in BIOS Setup Utility. Hard disk drive. System board.
021x	Keyboard error and two short beeps.	Run interactive tests of the keyboard and the auxiliary input device.
0220	Monitor type error-Monitor type does not match the one specified in CMOS.	Load Setup Defaults in BIOS Setup Utility.
0230	Shadow RAM error-Shadow RAM fails at offset nnnn.	System board.
0231	System RAM error-System RAM fails at offset nnnn.	DIMM. System board.
0232	Extended RAM error- Extended RAM fails at offset nnnn.	DIMM. System board.
0250	System battery error-System battery is dead.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0251	System CMOS checksum bad-Default configuration used.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0252	Password checksum bad-The password is cleared.	Reset the password by running BIOS Setup Utility.
0260	System timer error.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date. System board.
0270	Real-time clock error.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date. System board.
0271	Date and time error-Neither the date nor the time is set in the computer.	Run BIOS Setup Utility to reset the time and date.
0280	Previous boot incomplete-Default configuration used.	Load “Setup Default” in BIOS Setup Utility. DIMM. System board.
02F0	CPU ID:xx Failed.	CPU. System board.
02F4	EISA CMOS not writable.	Load Setup Defaults in BIOS Setup Utility. Replace the backup battery. System board.
02F5	DMA test failed.	DIMM. System board.
02F6	Software NMI failed.	DIMM. System board.
02F7	Fail-safe timer NMI failed.	DIMM. System board.
1802	Unauthorized network card is plugged in-Turn off and remove the miniPCI network card and two short beeps.	Remove Mini PCI network card. System board.	1802_Error
1803	Unauthorized daughter card is plugged in-Turn off and remove the daughter card.	Remove the daughter card that you installed. System board.	1802_Error
1804	Unauthorized WAN card is plugged in-Power off and remove the WAN card.	Remove the WAN card that you installed. System board.	1802_Error
1805	Unauthorized Wireless USB card is plugged in-Power off and remove the Wireless USB card.	Remove the Wireless USB card that you installed. System board.
1820	More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system.	Remove all but the reader that you set up for the authentication.
1830	Invalid memory configuration-Power off and install a memory module to Slot-0 or the lower slot.	Install DIMM in Slot-0, but not in Slot-1. Note: For the construction of the DIMM slot, see DIMM removal and installation - ThinkPad T400, R400.
2000	Hard Drive Active Protection sensor diagnostics failed.Press ESC to continue.Press F1 to enter SETUP	Undock docking station or port replicator if it is attached to the ThinkPad Notebook. Place the ThinkPad Notebook on a horizontal surface. Do not apply any physical shock to the computer. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
2010	Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed.	Inform the following information to the customer: If in the primary bay the customer is using a non-IBM or non-Lenovo hard disk drive (HDD), or an old generation IBM HDD which is not supported by this system, with the risk in mind, the customer can still use it by pressing ESC. If in the primary drive bay the customer is using a supported IBM/Lenovo HDD with an old firmware, the customer needs to update its firmware to the latest. The latest version is available at Lenovo Support & downloads.	2010 Error
2100	Initialization error on HDD0 (Main hard disk drive)	Reseat the hard disk drive. Main hard disk drive. System board.
2102	Initialization error on HDD1 (Ultrabay hard disk drive)	Reseat the hard disk drive. Ultrabay™ hard disk drive. System board.
2110	Read error on HDD0 (Main hard disk drive)	Reseat the hard disk drive. Main hard disk drive. System board.
2112	Read error on HDD1 (Ultrabay hard disk drive)	Reseat the hard disk drive. Ultrabay hard disk drive. System board.