Error Codes: Unterschied zwischen den Versionen

Aus ThinkPad-Wiki
Keine Bearbeitungszusammenfassung
(33 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 1: Zeile 1:
[[Bild:Qsicon_inArbeit.png]]
[[Bild:Qsicon_inArbeit.png]]


== Piep  Symptome ==
Hier sind die aus den jeweiligen Hardware Maintenance Manuals fast aller ThinkPad-Generationen die Fehlercodes aufgelistet. - Zusätzlich wurden undokumentierte Fehlercodes ergänzt.
 
Die rechte Spalte enthält Links zur Ursachensuche und eventuelle Behebungsmöglichkeiten.
   
   
{| class="wikitable"
{| class="wikitable"
Zeile 7: Zeile 9:
! FRU  or  action,  in  sequence
! FRU  or  action,  in  sequence
! Siehe auch
! Siehe auch
|-
|One  beep  and  Message <br>
CMOS Checksum error<br>
Set date and Time<br>
Press <F1> for setup
|1.      Replace CMOS Battery. <br>
2.      Check polarity of CMOS battery cable. <br>
3.      Check connector socket and soldering
|
|-
|-
|One  beep  and  a  blank, unreadable,  or  flashing  LCD.  
|One  beep  and  a  blank, unreadable,  or  flashing  LCD.  
Zeile 17: Zeile 28:
|One  long  and  two  short  beeps, and  a  blank  or  unreadable LCD.  
|One  long  and  two  short  beeps, and  a  blank  or  unreadable LCD.  
|1.      System  board. <br>
|1.      System  board. <br>
2.      LCD  assembly.  
2.      LCD  assembly. <br>
3.DIMM.
3.DIMM.
|[http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T61p-exhibiting-1-long-and-2-short-beep-and-black-screen/td-p/223574 nVidia Bug bei T61/R61]
|[http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T61p-exhibiting-1-long-and-2-short-beep-and-black-screen/td-p/223574 nVidia Bug bei T61/R61]
Zeile 31: Zeile 42:
|-
|-
|Three  short  beeps,  pause, three  more  short  beeps,  and one  short  beep. <br>
|Three  short  beeps,  pause, three  more  short  beeps,  and one  short  beep. <br>
One  short  beep,  pause,  three short  beeps,  pause,  three  more short  beeps,  and  one  short beep.  
One  short  beep,  pause,  three short  beeps,  pause,  three  more short  beeps,  and  one  short beep.<br>
One  short  beep,  pause,  three short  beeps,  pause,  four  more short  beeps,  and  three  short beeps.  
|1.      DIMM. <br>
|1.      DIMM. <br>
2.      System  board  
2.      System  board  
Zeile 38: Zeile 50:
|Only  the  cursor  appears.   
|Only  the  cursor  appears.   
|Reinstall  the  operating system.  
|Reinstall  the  operating system.  
|
|[[Fehlersuche_bei_ThinkPads#HDD_bootet_nach_Klonen_nicht.2C_nur_blinkender_Cursor_links_oben_sichtbar|Fehler beim Klonen]]
|-
|-
|Four  cycles  of  four  short  beeps and  a  blank  screen.  
|Four  cycles  of  four  short  beeps and  a  blank  screen.  
Zeile 47: Zeile 59:
|System  board
|System  board
|
|
|-
!colspan="3"| Nach Einspielen eines "Custom-/Mod-BIOS"
|-
|Two cycles of five short beeps but boots then.
|Security chip does not like Custom-BIOS
|[http://thinkpad-forum.de/threads/162420-gel%F6st-x201-custom-BIOS-WL-entfernt Disable security chip in BIOS]
|-
!colspan="3"| Undokumentiert
|-
|Three long beeps, pause, two short beeps
|Wrong placed ram.<br>Remove the CMOS battery and the RAM and insert them again or replace RAM
|[https://forums.tomsguide.com/threads/3-long-2-short-beeps.392681/ 3 long 2 short beeps] (tomsguide.com)
|-
|One short beep pause four short beeps pause one short beep pause one short beep
|It does sound like a RAM-slot is bad.
|[https://forums.lenovo.com/t5/ThinkPad-T61-and-prior-T-series/T43-Memory-Upgrade-Failure-1-4-1-1-Beep-Code/td-p/80640 1-4-1-1] (forums.lenovo.com)
|}
<br>
==Ohne Pieptöne - Symptome==
{| class="wikitable"
! Symptom or error 
!FRU or action, in sequence 
|-
|No beep, power-on indicator on, LCD blank, and no POST. 
|1. Make sure that every connector is connected tightly and correctly. <br>
2. DIMM.  <br>
3. System board. 
|-
| No beep, power-on indicator on, and LCD blank during POST. 
|1. Reseat DIMM.  <br>
2. System board. 
|-
|The power-on password prompt appears. 
|A power-on password or a supervisor password is set.  <br>
Type the password and press Enter. 
|-
|The hard-disk password prompt appears. 
|A hard-disk password is set. <br>
Type the password and press Enter. 
|}
|}
<br><br>


== Fehlermeldungen ==
== Fehlermeldungen ==
Zeile 112: Zeile 164:
Restore  it from  a  recovery  CD
Restore  it from  a  recovery  CD
|
|
|-
|System Security - Bottom cover tamper detected und verlangt ein Passwort
|
|Lösung: Das Kennwort wird vom System selbst gesetzt und lautet "lenovo"
Durch Eingabe des Kennwort kann man das tamper detected im BIOS deaktivieren.
|}
|}
<br><br>
<br><br>


== Numerische Fehler Codes ==
== Numerische Fehler Codes ==
 
=== Errorcodes Bereich 0xxx ===
{| class="wikitable"
{| class="wikitable"
! Error code
! Error code
Zeile 160: Zeile 217:
|Invalid RFID Serialization Information Area.
|Invalid RFID Serialization Information Area.
|System board.
|System board.
|
|[http://thinkpad-forum.de/threads/154608-0188-Error-Fehlercode-beim-T60 Lösung]
|-
|-
|0189  
|0189  
|Invalid RFID configuration information area-The EEPROM checksum is not correct.
|Invalid RFID configuration information area-The EEPROM checksum is not correct.
|System board.
|System board.
|
|[http://thinkpad-forum.de/threads/92985-L%C3%B6sung-X32-Bios-Error-0189 Lösung]
|-
|-
|0190  
|0190  
Zeile 269: Zeile 326:
|Password checksum bad-The password is cleared.
|Password checksum bad-The password is cleared.
|Reset the password by running BIOS Setup Utility.
|Reset the password by running BIOS Setup Utility.
|
|-
|0254
|System NV7 Volume checksum bad- Default configuration used (two short beeps)
|Turn off the computer and discharge CMOS. Then restart the computer.
|
|
|-
|-
Zeile 335: Zeile 397:
#    System board.  
#    System board.  
|
|
|}
=== Errorcodes Bereich 1xxx ===
{| class="wikitable"
! Error code
! Symptom
! FRU or action, in sequence
! Siehe auch
|-
|-
|1802
|1802
Zeile 375: Zeile 444:
'''Note''': For the construction of the DIMM slot, see DIMM removal and installation - ThinkPad T400, R400.
'''Note''': For the construction of the DIMM slot, see DIMM removal and installation - ThinkPad T400, R400.
|
|
|}
=== Errorcodes Bereich 2xxx ===
{| class="wikitable"
! Error code
! Symptom
! FRU or action, in sequence
! Siehe auch
|-
|-
|2000
|2000
Zeile 395: Zeile 471:
#    Main hard disk drive.
#    Main hard disk drive.
#    System board.  
#    System board.  
|[http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/t410s-SSD-errors-2100-HDD0/m-p/224653#M25217 eine Lösungsmöglichkeit im Lenovo-Forum]
|
* [http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/t410s-SSD-errors-2100-HDD0/m-p/224653#M25217 eine Lösungsmöglichkeit im Lenovo-Forum]
* [https://thinkpad-forum.de/threads/l%C3%B6sung-2100-detection-error-on-hdd.232669/ Sicherung F1 defekt (ThinkPad-Forum)]
|-
|-
|2102
|2102
Zeile 420: Zeile 498:
#    System board.  
#    System board.  
|
|
|-
|2200
|Machine Type and Serial Number are invalid.
|
#Replace the system board.
#Seriennummer setzen
|[https://thinkpad-forum.de/threads/199340-Hardware-Maintenance-Disk-1-89 Seriennummer setzen]<br>[https://thinkpad-forum.de/threads/228760-X250-Mainboardtausch-Seriennummer-Typnummer-eintragen-EEPROM-write-protected Beachte diesen Thread]
|-
|2201
|Machine UUID is invalid
|
#Replace the system board.
#UUID setzen
|[https://thinkpad-forum.de/threads/199340-Hardware-Maintenance-Disk-1-89 UUID setzen]<br>[https://thinkpad-forum.de/threads/228760-X250-Mainboardtausch-Seriennummer-Typnummer-eintragen-EEPROM-write-protected Beachte diesen Thread]
|}
|}
<br><br>
<br><br>


== Symptome ohne Piepton ==
== Symptome ohne Piepton ==
Zeile 526: Zeile 617:
# Detach the expansion unit if it is attached to the computer.<br>
# Detach the expansion unit if it is attached to the computer.<br>
# System board<br>
# System board<br>
| [http://support.lenovo.com/en_US/detail.page?LegacyDocID=NDEX-HMM Hardware Maintenance Manual]
| [https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|-
|
|
Zeile 535: Zeile 626:
# Expansion unit or port replicator.
# Expansion unit or port replicator.
# System board
# System board
|[http://support.lenovo.com/en_US/detail.page?LegacyDocID=NDEX-HMM Hardware Maintenance Manual]
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|-
|11XX<br>
|11XX<br>
Zeile 590: Zeile 681:
# Hard disk drive assembly
# Hard disk drive assembly
# System board
# System board
|[http://support.lenovo.com/en_US/detail.page?LegacyDocID=NDEX-HMM Hardware Maintenance Manual]
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|-
|175, 177, 178<br>
|175, 177, 178<br>
Zeile 637: Zeile 728:
(A depleted battery pack was installed when the power was on.)
(A depleted battery pack was installed when the power was on.)
|Go to “Checking the Battery Pack” in Hardware Maintenance Manual.
|Go to “Checking the Battery Pack” in Hardware Maintenance Manual.
|[http://support.lenovo.com/en_US/detail.page?LegacyDocID=NDEX-HMM Hardware Maintenance Manual]
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|-
|191XX<br>
|191XX<br>
Zeile 682: Zeile 773:
|System board
|System board
|
|
|-
|1XX 
|System board
|
|-
|2XX<br>
201: Memory data error.<br>
202: Memory line error 00–15. <br>
203: Memory line error 16–23.<br>
205: Memory test failure on on-board memory.<br>
221: ROM to RAM remap error.
|
# Go to “Memory Checkout” - siehe rechts.<br>
# DIMM card<br>
# System board
|201: leere BIOS-Batterie, z.B. bei [[701]]
[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|225 (Unsupported memory module.)
|
# Check if the supported DIMM is installed.
# DIMM card
# System board
|
|-
|301, 303, 304, 305, 3XX<br>
(301: Keyboard error.)
|
# Go to “Keyboard or Auxiliary Input Device Checkout” -siehe rechts.
# Keyboard
# External numeric keypad
# External keyboard
# Keyboard/mouse cable
# System board
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|601, 6XX<br>
(601: Diskette drive or controller error.)
|
# Go to “Diskette Drive Checkout” - siehe rechts.
# Diskette drive assembly
# Diskette
# System board
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|602<br>
(Diskette read error.)
|
# Go to “Diskette Drive Checkout” - siehe rechts.
# Diskette
# Diskette drive assembly
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|604<br>
(Unacceptable ID was read from the diskette drive.)
|
# Go to “Diskette Drive Checkout” - siehe rechts.
# Diskette drive assembly
# System board
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|-
|2402
|TV Out Card
|
|-
|24XX<br>
(2401: System board video error.)
|System board
|
|-
|808X<br>
8081: PCMCIA presence test failure. (PCMCIA revision number also checked.)<br>
8082: PCMCIA register test failure.
|
# PC Card slot assembly
# PCMCIA device
# System board
|
|-
|860X<br>
(Pointing device error when TrackPoint is disabled.)<br>
8601: System bus error–8042 mouse interface.
8602: External mouse error.<br>
8603: System bus error or mouse error.
|
# External mouse
# External keyboard
# System board
|
|-
|861X<br>
(Pointing device error when TrackPoint is enabled.)<br>
8611: System bus error–I/F between 8042 and IPDC.<br>
8612: TrackPoint error.<br>
8613: System board or TrackPoint error.
|
# Reseat the keyboard cable on the sub card.
# Keyboard
# External mouse
# Sub card
# System board
|
|-
|I9990301<br>
I9990302<br>
I9990305<br>
I9990301: Hard disk error.<br>
I9990302: Invalid hard disk boot record.<br>
I9990305: No bootable device.<br>
|
# Check that the operating system is installed in the hard disk drive. If not, install the operating system.
# Reseat the boot device.
# Check the startup sequence for the correct boot device.
# Check that the operating system has no failure and is installed correctly.
|
|-
|I9990303<br>
(Bank–2 flash ROM check sum error.)
|
System board Other codes not listed above.<br>
Go to “Undetermined Problems” - siehe rechts.
|[https://download.lenovo.com/eol/hmm_notebook.html Hardware Maintenance Manual]
|}
|}
<br><br>
== Undokumentierte Fehlercodes ==
{| class="wikitable"
! Symptom  or  error 
! FRU  or  action,  in  sequence
! Siehe auch
|-
|00127<br>
Nach CPU-Upgrade (Thinkpad 600, 770 etc), kann das Bios den L2-Cache der CPU nicht initialisieren
|BIOS "Hack" - siehe rechts
|
#[[770X#Error_127_beheben|Error 127 beheben]]
#[[600E#Onboard-Speicher_abschalten|Onboard-RAM abschalten]]
|}
<br><br>
== Fehlercodes von PS/2 Computern ==
Diese Sammlung stammt aus dem Buch "Upgrading and Repairing PCs" und ist eine Zusammenstellung aus IBM Technical Reference Manuals und IBM Hardware Maintenance Service Manuals.
{| class="wikitable"
| Error Code Beschreibung 
|-
  01x  Undetermined problem errors
  02x  Power supply errors
  1xx  System Board Errors
  101  System Board Error; Interrupt failure
  102  System Board Error; Timer failure
  103  System Board Error; Timer Interrupt failure
  104  System Board Error; Protected mode failure
  105  System Board Error; Last 8042 command not accepted
  106  System Board Error; Converting logic test
  107  System Board Error; Hot Non Maskable Interrupt test
  108  System Board Error; Timer bus test
  109  System Board Error; Memory select error
  110  PS/2 System Board Error; Parity check error
  111  PS/2 Memory adaptor error
  112  PS/2 MicroChannel arbitration error
  113  PS/2 MicroChannel arbitration error
  121  Unexpected hardware interrupts occured
  131  PC system board cassette port wrap test failure
  161  System Options Not Set-(Run SETUP); Dead battery
  162  System Options Not Set-(Run SETUP);
        CMOS checksum/configuration error
  163  Time & Date Not Set-(Run SETUP); Clock not updating
  164  Memory Size Error-(Run SETUP);
        CMOS setting does not match memory
  165  PS/2 System options not set
  166  PS/2 MicroChannel adapter timeout error
  199  User indicated INSTALLED DEVICES list is not correct
  2xx  Memory (RAM) errors
  201  Memory test failure, error location will be displayed
        in hexadecimal
  202  Memory address error, address lines 00-15
  203  Memory address error, address lines 16-23
  215  PS/2 Motherboard memory failure
  216  PS/2 Motherboard memory failure
  3xx  Keyboard errors
  301  Keyboard did not respond to software reset or a stuck
        key failure was detected.  If a stuck key was detected,
        the scan code for the key is displayed in hexadecimal.
  302  System Unit Keylock is Locked
  303  Keyboard or System Unit Error
  304  Keyboard or System Unit Error; Keyboard clock high
  305  PS/2 Keyboard fuse (on system board) error
  4xx  Monochrome Display Adapter (MDA) errors
  4xx  PS/2 System board parallel port errors
  401  Monochrome memory test, horizontal sync frequency test,
        or video test failure
  401  PS/2 System board parallel port failure
  408  User indicated display attributes failure
  416  User indicated character set failure
  424  User indicated 80x25 mode failure
  432  Parallel port test failure; monochrome display adapter
  5xx  Color Graphics Adapter (CGA) errors
  501  CGA memory test, horizontal sync frequency test, or video
        test failure
  508  User indicated display attribute failure
  516  User indicated character set failure
  524  User indicated 80x25 mode failure
  532  User indicated 40x25 mode failure
  540  User indicated 320x200 graphics mode failure
  548  User indicated 640x200 graphics mode failure
  6xx  Floppy drive/adapter errors
  601  Floppy drive/adapter Power On Self Test failure
  602  Drive test failure; disk boot record not valid
  606  Drive changeline function failure; drive error
  607  Disk is write protected; drive error
  608  Bad command; drive error
  610  Disk initialization failure; track 0 bad
  611  Timeout; drive error
  612  Bad Controller chip
  613  Bad Direct Memory Access; drive error
  614  Bad Direct Memory Access; boundary overrun
  615  Bad index timing; drive error
  616  Drive speed error
  621  Bad seek; drive error
  622  Bad Cyclic Redundancy Check; drive error
  623  Record not found; drive error
  624  Bad address mark; drive error
  625  Bad Controller chip; seek error
  626  Disk data compare error
  7xx  8087, 80287 or 80387 math coprocessor errors
  9xx  Parallel printer adapter errors
  901  Parallel printer adapter test failure
  10xx  Alternate parallel printer adapter errors
  1001  Alternate parallel printer adapter test failure
  11xx  Asynchronous communications adapter errors
  11xx  PS/2 System board async port errors
  1101  Asynchronous communications adapter test failure
  1102  PS/2 System board async port or serial device error
  1106  PS/2 System board async port or serial device error
  1107  PS/2 System board async port or serial cable error
  1108  PS/2 System board async port or serial device error
  1109  PS/2 System board async port or serial device error
  1112  PS/2 System board async port error
  1118  PS/2 System board async port error
  1119  PS/2 System board async port error
  12xx  Alternate asynchronous communications adapter errors
  12xx  PS/2 Dual async adapter error
  1201  Alternate asynchronous communications adapter test failure
  1202  PS/2 Dual async adapter or serial device error
  1206
  1207  PS/2 Dual async adapter or serial cable error
  1208  PS/2 Dual async adapter or serial device error
  1209
  1212  PS/2 Dual async adapter or system board error
  1218
  1219
  1227
  1233
  1234
  13xx  Game control adapter errors
  1301  Game control adapter test failure
  1301  Joy-stick test failure
  14xx  Matrix Printer errors
  15xx  Synchronous data link control (SDLC) communications
        adapter errors
  1510  8255 port B failure
  1511  8255 port A failure
  1512  8255 port C failure
  1513  8253 timer 1 did not reach terminal count
  1514  8253 timer 1 stuck on
  1515  8253 timer 0 did not reach terminal count
  1516  8253 timer 0 stuck on
  1517  8253 timer 2 did not reach terminal count
  1518  8253 timer 2 stuck on
  1519  8273 port B error
  1520  8273 port A error
  1521  8273 command/read timeout
  1522  Interrupt level 4 failure
  1523  Ring Indicate stuck on
  1524  Receive clock stuck on
  1525  Transmit clock stuck on
  1526  Test indicate stuck on
  1527  Ring indicate not on
  1528  Receive clock not on
  1529  Transmit clock not on
  1530  Test indicate not on
  1531  Data set ready not on
  1532  Carrier detect not on
  1533  Clear to send not on
  1534  Data set ready stuck on
  1536  Clear to send stuck on
  1537  Level 3 interrupt failure
  1538  Receive interrupt results error
  1539  Wrap data compare error
  1540  Direct Memory Access channel 1 error
  1541  Direct Memory Access channel 1 error
  1542  Error in 8273 error checking or status reporting
  1547  Stray interrupt level 4
  1548  Stray interrupt level 3
  1549  Interrupt presentation sequence timeout
  16xx  Display emulation errors (327x, 5520, 525x)
  17xx  Fixed disk errors
  1701  Fixed disk POST error
  1702  Fixed disk adapter error
  1703  Fixed disk drive error
  1704  Fixed disk adapter or drive error
  1780  Fixed disk 0 failure
  1781  Fixed disk 1 failure
  1782  Fixed disk controller failure
  1790  Fixed disk 0 error
  1791  Fixed disk 1 error
  18xx  I/O expansion unit errors
  1801  I/O expansion unit POST error
  1810  Enable/Disable failure
  1811  Extender card wrap test failure; disabled
  1812  High order address lines failure; disabled
  1813  Wait state failure; disabled
  1814  Enable/Disable could not be set on
  1815  Wait state failure; disabled
  1816  Extender card wrap test failure; enabled
  1817  High order address lines failure; enabled
  1818  Disable not functioning
  1819  Wait request switch not set correctly
  1820  Receiver card wrap test failure
  1821  Receiver high order address lines failure
  19xx  3270 PC attachment card errors
  20xx  Binary synchronous (BSC) adapter errors
  2010  8255 port A failure
  2011  8255 port B failure
  2012  8255 port C failure
  2013  8253 timer 1 did not reach terminal count
  2014  8253 timer 1 stuck on
  2015  8253 timer 2 did not reach terminal count or
        timer 2 stuck on
  2017  8251 Data set ready failed to come on
  2018  8251 Clear to send not sensed
  2019  8251 Data set ready stuck on
  2020  8251 Clear to send stuck on
  2021  8251 hardware reset failure
  2022  8251 software reset failure
  2023  8251 software "error reset" failure
  2024  8251 transmit ready did not come on
  2025  8251 receive ready did not come on
  2026  8251 could not force "overrun" error status
  2027  Interrupt failure; no timer interrupt
  2028  Interrupt failure; transmit, replace card or planar
  2029  Interrupt failure; transmit, replace card
  2030  Interrupt failure; receive, replace card or planar
  2031  Interrupt failure; receive, replace card
  2033  Ring indicate stuck on
  2034  Receive clock stuck on
  2035  Transmit clock stuck on
  2036  Test indicate stuck on
  2037  Ring indicate stuck on
  2038  Receive clock not on
  2039  Transmit clock not on
  2040  Test indicate not on
  2041  Data set ready not on
  2042  Carrier detect not on
  2043  Clear to send not on
  2044  Data set ready stuck on
  2045  Carrier detect stuck on
  2046  Clear to send stuck on
  2047  Unexpected transmit interrupt
  2048  Unexpected receive interrupt
  2049  Transmit data did not equal receive data
  2050  8251 detected overrun error
  2051  Lost data set ready during data wrap
  2052  Receive timeout during data wrap
  21xx  Alternate binary synchronous communications adapter errors
  2110  8255 port A failure
  2111  8255 port B failure
  2112  8255 port C failure
  2113  8253 timer 1 did not reach terminal count
  2114  8253 timer 1 stuck on
  2115  8253 timer 2 did not reach terminal count or
        timer 2 stuck on.
  2117  8251 Data set ready failed to come on
  2118  8251 Clear to send not sensed
  2119  8251 Data set ready stuck on
  2120  8251 Clear to send stuck on
  2121  8251 hardware reset failure
  2122  8251 software reset failure
  2123  8251 software "error reset" failure
  2124  8251 transmit ready did not come on
  2125  8251 receive ready did not come on
  2126  8251 could not force "overrun" error status
  2127  Interrupt failure; no timer interrupt
  2128  Interrupt failure; transmit, replace card or planar
  2129  Interrupt failure; transmit, replace card
  2130  Interrupt failure; receive, replace card or planar
  2131  Interrupt failure; receive, replace card
  2133  Ring indicate stuck on
  2134  Receive clock stuck on
  2135  Transmit clock stuck on
  2136  Test indicate stuck on
  2137  Ring indicate stuck on
  2138  Receive clock not on
  2139  Transmit clock not on
  2140  Test indicate not on
  2141  Data set ready not on
  2142  Carrier detect not on
  2143  Clear to send not on
  2144  Data set ready stuck on
  2145  Carrier detect stuck on
  2146  Clear to send stuck on
  2147  Unexpected transmit interrupt
  2148  Unexpected receive interrupt
  2149  Transmit Data did not equal receive data
  2150  8251 detected overrun error
  2151  Lost data set ready during data wrap
  2152  Receive timeout during data wrap
  22xx  Cluster adapter errors
  24xx  Enhanced Graphics Adapter (EGA) errors
  24xx  PS/2 System board Video Graphics Array (VGA) errors
  26xx  XT/370 errors
  27xx  AT/370 errors
  28xx  3278/79 emulation adapter errors
  29xx  Color/graphics printer errors
  30xx  Primary PC Network adapter error
  3001  Processor test failure
  3002  ROM checksum test failure
  3003  Unit ID PROM test failure
  3004  RAM test failure
  3005  Host Interface Controller test failure
  3006  +/- 12v test failure
  3007  Digital loopback test failure
  3008  Host detected Host Interface Controller failure
  3009  Sync failure and no Go bit
  3010  Host Interface Controller test OK and no Go bit
  3011  Go bit and no Command 41
  3012  Card not present
  3013  Digital failure; fall through
  3015  Analog failure
  3041  Hot carrier; not this card
  3042  Hot carrier; this card!
  31xx  Secondary PC Network adapter errors
  3101  Processor test failure
  3102  ROM check test failure
  3103  Unit ID PROM test failure
  3104  RAM test failure
  3105  Host Interface Controller test failure
  3106  +/- 12v test failure
  3107  Digital loopback test failure
  3108  Host detected Host Interface Controller failure
  3109  Sync failure and no Go bit
  3110  Host Interface Controller test OK and no Go bit
  3111  Go bit and no Command 41
  3112  Card not present
  3113  Digital failure; fall through
  3115  Analog failure
  3141  Hot carrier; not this card
  3142  Hot carrier; this card!
  33xx  Compact printer errors
  36xx  General Purpose Interface Bus (GPIB) adapter errors
  38xx  Data acquisition adapter errors
  39xx  Professional graphics controller errors
  71xx  Voice communications adapter errors
  73xx  3.5" external diskette drive errors
  7306  Disk changeline function failure; track 0 bad
  7307  Disk is write protected; drive error
  7308  Bad command; drive error
  7310  Disk initialization failure; track 0 bad
  7311  Timeout; drive error
  7312  Bad Controller chip
  7313  Bad Direct Memory Access; drive error
  7314  Bad Direct Memory Access; boundary overrun
  7315  Bad index timing; drive error
  7316  Drive speed error
  7321  Bad seek; drive error
  7322  Bad Cyclic Redundancy Check; drive error
  7323  Record not found; drive error
  7324  Bad address mark; drive error
  7325  Bad Controller chip; seek error
  74xx  IBM PS/2 Display adapter (VGA card) errors
  85xx  IBM Expanded Memory Adapter (XMA) errors
  86xx  PS/2 Pointing device errors
  8601  PS/2 Pointing device error
  8602  PS/2 Pointing device error
  8603  PS/2 Pointing device error or System board failure
  89xx  Music feature card errors
  100xx PS/2 Multiprotocol adapter errors
  10002 PS/2 Multiprotocol adapter or serial device error
  10006 PS/2 Multiprotocol adapter or serial device error
  10007 PS/2 Multiprotocol adapter or communications cable error
  10008 PS/2 Multiprotocol adapter or serial device error
  10009 PS/2 Multiprotocol adapter or serial device error
  10012 PS/2 Multiprotocol adapter or system board error.
  10018
  10019
  10042
  10056
  104xx PS/2 ESDI Fixed disk errors
  10480 PS/2 ESDI Fixed disk 0 failure
  10481 PS/2 ESDI Fixed disk 1 failure
  10482 PS/2 ESDI Fixed disk controller failure
  10483 PS/2 ESDI Fixed disk controller failure
  10490 PS/2 ESDI Fixed disk 0 error
  10491 PS/2 ESDI Fixed disk 1 error
|}
<br><br>


== Weblinks ==
== Weblinks ==
* siehe auch Wiki-Artikel [[Fehlersuche bei ThinkPads]]
* [http://support.lenovo.com/en_US/downloads/detail.page?DocID=HT002759 Numeric error codes - ThinkPad R400, T400]
* [http://support.lenovo.com/en_US/downloads/detail.page?DocID=HT002759 Numeric error codes - ThinkPad R400, T400]
* [http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=DJON-3LXQX8 Numeric error codes - ThinkPad 770]
* [http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=DJON-3LXQX8 Numeric error codes - ThinkPad 770]
* [http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=LWIK-3PCLMK Beep and no beep symptoms - ThinkPad 560X]
* [http://ps-2.kev009.com/pcpartnerinfo/ctstips/5056.htm Beep and no beep symptoms - ThinkPad 560X]
* [http://support.lenovo.com/en_US/downloads/detail.page?DocID=HT035729 Beep and no beep symptoms - ThinkPad General]
* [http://support.lenovo.com/en_US/downloads/detail.page?DocID=HT035729 Beep and no beep symptoms - ThinkPad General]
* [http://support.lenovo.com/en_US/downloads/detail.page?DocID=HT005068 Beep and No beep symptoms - ThinkPad R500]
* [http://support.lenovo.com/en_US/downloads/detail.page?DocID=HT005068 Beep and No beep symptoms - ThinkPad R500]
* [http://www.comptechdoc.org/hardware/beepcodes/3.htm Phoenix BIOS beep codes]
* [http://www.comptechdoc.org/hardware/beepcodes/3.htm Phoenix BIOS beep codes]
 
* [http://ps-2.kev009.com/pcpartnerinfo/ctstips/2c86.htm FRU-Codes am Beispiel ThinkPad 560x]
[[Category:Fehlermeldung]]
[[Category:Fehlermeldung]]

Version vom 21. Mai 2022, 18:56 Uhr

Qsicon inArbeit.png

Hier sind die aus den jeweiligen Hardware Maintenance Manuals fast aller ThinkPad-Generationen die Fehlercodes aufgelistet. - Zusätzlich wurden undokumentierte Fehlercodes ergänzt.

Die rechte Spalte enthält Links zur Ursachensuche und eventuelle Behebungsmöglichkeiten.

Symptom or error FRU or action, in sequence Siehe auch
One beep and Message

CMOS Checksum error
Set date and Time
Press <F1> for setup

1. Replace CMOS Battery.

2. Check polarity of CMOS battery cable.
3. Check connector socket and soldering

One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector.

2. LCD assembly.
3. External CRT.
4. System board.

One long and two short beeps, and a blank or unreadable LCD. 1. System board.

2. LCD assembly.
3.DIMM.

nVidia Bug bei T61/R61
Two short beeps with error codes. POST error. Numerische Fehler Codes
Two short beeps and a blank screen. 1. System board.

2. DIMM.

RAM-Steckplatz bei T30, R3x, X3x
Three short beeps, pause, three more short beeps, and one short beep.

One short beep, pause, three short beeps, pause, three more short beeps, and one short beep.
One short beep, pause, three short beeps, pause, four more short beeps, and three short beeps.

1. DIMM.

2. System board

Only the cursor appears. Reinstall the operating system. Fehler beim Klonen
Four cycles of four short beeps and a blank screen. System board (security chip)
Five short beeps and a blank screen. System board
Nach Einspielen eines "Custom-/Mod-BIOS"
Two cycles of five short beeps but boots then. Security chip does not like Custom-BIOS Disable security chip in BIOS
Undokumentiert
Three long beeps, pause, two short beeps Wrong placed ram.
Remove the CMOS battery and the RAM and insert them again or replace RAM
3 long 2 short beeps (tomsguide.com)
One short beep pause four short beeps pause one short beep pause one short beep It does sound like a RAM-slot is bad. 1-4-1-1 (forums.lenovo.com)


Ohne Pieptöne - Symptome

Symptom or error FRU or action, in sequence
No beep, power-on indicator on, LCD blank, and no POST. 1. Make sure that every connector is connected tightly and correctly.

2. DIMM.
3. System board.

No beep, power-on indicator on, and LCD blank during POST. 1. Reseat DIMM.

2. System board.

The power-on password prompt appears. A power-on password or a supervisor password is set.

Type the password and press Enter.

The hard-disk password prompt appears. A hard-disk password is set.

Type the password and press Enter.

Fehlermeldungen

Symptom or error FRU or action, in sequence Siehe auch
Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility.

2. Backup battery.
3. System board.

Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility.

2. Backup battery.
3. System board.

Failing bits: nnnn. 1. DIMM.

2. System board.

Invalid system configuration data. 1. DIMM.

2. System board.

I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility.

2. Backup battery.
3. System board.

Operating system not found. 1. Check that the operating system has no failure and is installed correctly.

2. Enter the BIOS Setup Utility and see whether the hard disk drive and the diskette drive are properly identified.
3. Reseat the hard disk drive.
4. Reinstall the operating system.
5. Diskette drive.
6. Hard disk drive.
7. System board.

Hibernation error. 1. Restore the system configuration to what it was before the computer entered hibernation mode.

2. If memory size has been changed, re-create the hibernation file.

Fan error. Fan.
Thermal sensing error. System board.

Fehlermeldung erscheint auch nach CPU-Upgrade z.B. bei T61

Thread im ThinkPad-Forum und T61 (Boardtausch)
Authentication of system services failed. Press <Esc> to resume. The Predesktop Area in the HDD is corrupted.

Restore it from a recovery CD

System Security - Bottom cover tamper detected und verlangt ein Passwort Lösung: Das Kennwort wird vom System selbst gesetzt und lautet "lenovo"

Durch Eingabe des Kennwort kann man das tamper detected im BIOS deaktivieren.



Numerische Fehler Codes

Errorcodes Bereich 0xxx

Error code Symptom FRU or action, in sequence Siehe auch
0175 Bad CRC1, stop POST task-The EEPROM checksum is not correct. System board siehe 0175: Bad CRC1
0176 System Security-The system has been tampered with.
  1. Run BIOS Setup Utility, and save the current setting by pressing F10.
  2. System board.
0177 Bad SVP data, stop POST task-The checksum of the supervisor password in the EEPROM is not correct. System board.
0182 Bad CRC2. Enter BIOS Setup and load Setup defaults.-The checksum of the CRS2 setting in the EEPROM is not correct.
  1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10.
  2. System board.
0185 Bad startup sequence settings. Enter BIOS Setup and load Setup defaults. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10.
0187 EAIA data access error-The access to EEPROM is failed. System board.
0188 Invalid RFID Serialization Information Area. System board. Lösung
0189 Invalid RFID configuration information area-The EEPROM checksum is not correct. System board. Lösung
0190 Critical low-battery error.
  1. Charge the battery pack.
  2. Battery pack.
0191 System Security-Invalid Remote Change requested.
  1. Run BIOS Setup Utility, and then save current setting by pressing F10.
  2. System board.
0192 System Security- Embedded Security hardware tamper detected. System board.
0199 System Security-Security password retry count exceeded.
  1. Run BIOS Setup Utility, and then save the current setting by pressing F10.
  2. System board.
01C8 Two or more modem devices are found. Remove all but one of them. Press ESC to continue.
  1. Remove either a Mini-PCI Card or a modem daughter card. Otherwise, press ESC to ignore the warning message.
  2. System board.
01C9 More than one Ethernet devices are found. Remove one of them. Press ESC to continue.
  1. Remove the Ethernet device that you installed; or press ESC to ignore the warning message.
  2. System board.
1802 Error
01CA More than one Wireless LAN devices are found. Remove one of them.
  1. Remove the wireless LAN device that you installed.
  2. System board.
0200 Hard disk error-The hard disk is not working.
  1. Reseat the hard disk drive.
  2. Load Setup Defaults in BIOS Setup Utility.
  3. Hard disk drive.
  4. System board.
021x Keyboard error and two short beeps. Run interactive tests of the keyboard and the auxiliary input device.
0220 Monitor type error-Monitor type does not match the one specified in CMOS. Load Setup Defaults in BIOS Setup Utility.
0230 Shadow RAM error-Shadow RAM fails at offset nnnn. System board.
0231 System RAM error-System RAM fails at offset nnnn.
  1. DIMM.
  2. System board.
0232 Extended RAM error- Extended RAM fails at offset nnnn.
  1. DIMM.
  2. System board.
0250 System battery error-System battery is dead.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0251 System CMOS checksum bad-Default configuration used.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0252 Password checksum bad-The password is cleared. Reset the password by running BIOS Setup Utility.
0254 System NV7 Volume checksum bad- Default configuration used (two short beeps) Turn off the computer and discharge CMOS. Then restart the computer.
0260 System timer error.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
  3. System board.
0270 Real-time clock error.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
  3. System board.
0271 Date and time error-Neither the date nor the time is set in the computer. Run BIOS Setup Utility to reset the time and date.
0280 Previous boot incomplete-Default configuration used.
  1. Load “Setup Default” in BIOS Setup Utility.
  2. DIMM.
  3. System board.
02F0 CPU ID:xx Failed.
  1. CPU.
  2. System board.
02F4 EISA CMOS not writable.
  1. Load Setup Defaults in BIOS Setup Utility.
  2. Replace the backup battery.
  3. System board.
02F5 DMA test failed.
  1. DIMM.
  2. System board.
02F6 Software NMI failed.
  1. DIMM.
  2. System board.
02F7 Fail-safe timer NMI failed.
  1. DIMM.
  2. System board.

Errorcodes Bereich 1xxx

Error code Symptom FRU or action, in sequence Siehe auch
1802 Unauthorized network card is plugged in-Turn off and remove the miniPCI network card and two short beeps.
  1. Remove Mini PCI network card.
  2. System board.
1802 Error
1803 Unauthorized daughter card is plugged in-Turn off and remove the daughter card.
  1. Remove the daughter card that you installed.
  2. System board.
1804 Unauthorized WAN card is plugged in-Power off and remove the WAN card.
  1. Remove the WAN card that you installed.
  2. System board.
1802 Error
1805 Unauthorized Wireless USB card is plugged in-Power off and remove the Wireless USB card.
  1. Remove the Wireless USB card that you installed.
  2. System board.
1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication.
1830 Invalid memory configuration-Power off and install a memory module to Slot-0 or the lower slot.
  1. Install DIMM in Slot-0, but not in Slot-1.

Note: For the construction of the DIMM slot, see DIMM removal and installation - ThinkPad T400, R400.

Errorcodes Bereich 2xxx

Error code Symptom FRU or action, in sequence Siehe auch
2000 Hard Drive Active Protection sensor diagnostics failed.Press ESC to continue.Press F1 to enter SETUP
  1. Undock docking station or port replicator if it is attached to the ThinkPad Notebook.
  2. Place the ThinkPad Notebook on a horizontal surface. Do not apply any physical shock to the computer.
  3. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
2010 Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed. Inform the following information to the customer: If in the primary bay the customer is using a non-IBM or non-Lenovo hard disk drive (HDD), or an old generation IBM HDD which is not supported by this system, with the risk in mind, the customer can still use it by pressing ESC. If in the primary drive bay the customer is using a supported IBM/Lenovo HDD with an old firmware, the customer needs to update its firmware to the latest. The latest version is available at Lenovo Support & downloads. 2010 Error
2100 Initialization error on HDD0 (Main hard disk drive)
  1. Reseat the hard disk drive.
  2. Main hard disk drive.
  3. System board.
2102 Initialization error on HDD1 (Ultrabay hard disk drive)
  1. Reseat the hard disk drive.
  2. Ultrabay™ hard disk drive.
  3. System board.
2110 Read error on HDD0 (Main hard disk drive)
  1. Reseat the hard disk drive.
  2. Main hard disk drive.
  3. System board.
2112 Read error on HDD1 (Ultrabay hard disk drive)
  1. Reseat the hard disk drive.
  2. Ultrabay hard disk drive.
  3. System board.
2200 Machine Type and Serial Number are invalid.
  1. Replace the system board.
  2. Seriennummer setzen
Seriennummer setzen
Beachte diesen Thread
2201 Machine UUID is invalid
  1. Replace the system board.
  2. UUID setzen
UUID setzen
Beachte diesen Thread



Symptome ohne Piepton

Symptom or error FRU or action, in sequence Siehe auch
No beep, power-on indicator on, LCD blank, and no POST. 1. Make sure that every connector is connected tightly and correctly.

2. DIMM.
3. System board.

No beep, power-on indicator on, and LCD blank during

POST.

1. Reseat DIMM.

2. System board.

RAM-Steckplatz bei T30, R3x, X3x
The power-on password prompt appears. A power-on password or a supervisor password is set.

Type the password and press Enter.

The hard-disk password prompt appears. A hard-disk password is set.

Type the password and press Enter.

The DOS full screen looks smaller than it should. Start the ThinkPad Configuration program (F1 at Boot-time) and set the Screen expansion function



LCD Symptome

Symptom or error FRU or action, in sequence Siehe auch
No beep, power-on indicator on, and a blank LCD during POST. System board.
  • LCD backlight not working.
  • LCD too dark.
  • LCD brightness cannot be adjusted.
  • LCD contrast cannot be adjusted.
1. Reseat the LCD connectors.

2. LCD assembly.
3. System board.

Sicherung für Hintergrundbeleuchtung durchgebrannt
  • LCD screen unreadable.
  • Characters missing pixels.
  • Screen abnormal.
  • Wrong color displayed.
1. See important note for “LCD-related symptoms.”1)

2. Reseat all LCD connectors.
3. LCD assembly.
4. System board.

Flexing
Horizontal or vertical lines displayed on LCD. LCD assembly.

1) Zitat aus dem Hardware Maintenance manual:

A bright dot means a pixel is always on (white or color.) A dark dot means a pixel is always off (black color.)



Numerische Fehlercodes (ThinkPads vor 2001)

Symptom or error FRU or action, in sequence Siehe auch
10X

101: Interrupt failure.
102: Timer failure.
103: Timer interrupt failure.
104: Protected mode failure.
105: Last 8042 command not accepted.
107: NMI test failure.
108: Timer bus test failure.
109: Low meg-chip select test.

  1. System board
110

(Planar parity.)

  1. Go to “Memory Checkout” siehe rechte Spalte
  2. DIMM card
  3. Detach the expansion unit if it is attached to the computer.
  4. System board
Hardware Maintenance Manual

111
(I/O parity.)

  1. Go to “Memory Checkout” siehe rechte Spalte
  2. Expansion unit or port replicator.
  3. System board
Hardware Maintenance Manual
11XX

1101: Serial_A test failure.

  1. Serial device
  2. Communication cable
  3. System board
12XX

1201: Serial_B test failure.

  1. System board (infrared)
158

(The hard disk password was not set even though the supervisor password is set.)

Set the password for the hard disk drive.
159

(The hard disk password is not set the same as the supervisor password.)

Set the correct password for the hard disk drive.
161

(Dead battery.)

  1. Go to “Checking the Backup Battery” 1.
  2. Backup battery
  3. System board
163

(Time and date were not set.)

  1. Set time and date.
  2. System board
173

(Configuration data was lost.)

  1. Select OK in the error screen; then set the time and date.
  2. Backup battery
  3. System board
174

(Configuration error: Perform “Checking the Installed Devices List” (siehe rechte Spalte) before changing any FRUs.)

  1. Check device configuration.
  2. Hard disk drive assembly
  3. System board
Hardware Maintenance Manual
175, 177, 178

175: EEPROM CRC #1 error.
177: Supervisor password check sum error.
178: EEPROM is not functional.

  1. System board
17XX

1701: Hard disk controller failure.
1780, 1790: Hard disk 0 error.
1781, 1791: Hard disk 1 error.

  1. Hard disk drive
  2. System board
183

(Incorrect password entered at the supervisor password prompt.)

Have the user examine the password.
184

(Power-on password check sum error.)

Reset the power-on password in Easy-Setup.
185

(The startup sequence is not valid. Suspect that power was off when the startup sequence was being updated.)

Reset the startup sequence in Easy-Setup.
186 System board
188, 189

(BAD EEPROM CRC #1. An incorrect checksum of the EEPROM is received.)

System board

190
(A depleted battery pack was installed when the power was on.)

Go to “Checking the Battery Pack” in Hardware Maintenance Manual. Hardware Maintenance Manual
191XX

(PM initialization error.)

System board

192
(Fan error.)

  1. Measure the voltage of the backup battery. If the voltage is not correct, replace the backup battery.
  2. Fan
  3. System board
193

(RF Antenna has been removed.)

  1. Type the correct Supervisor Password at the password prompt.
  2. Reseat the RF Antenna to the HDD cover.
194

(The computer is carried through the portal gate.)

Type the correct Supervisor Password at the password prompt.

195

(The configuration read from the hibernation area does not match the actual configuration.)

Check if the configuration was changed. For example, check if the DIMM card is added.
196

(A read error occurred in the hibernation area of the hard disk drive.)

  1. Run the hard disk drive test.
  2. Hard disk drive
199XX

(Resume error.)

System board
1XX System board
2XX

201: Memory data error.
202: Memory line error 00–15.
203: Memory line error 16–23.
205: Memory test failure on on-board memory.
221: ROM to RAM remap error.

  1. Go to “Memory Checkout” - siehe rechts.
  2. DIMM card
  3. System board
201: leere BIOS-Batterie, z.B. bei 701

Hardware Maintenance Manual

225 (Unsupported memory module.)
  1. Check if the supported DIMM is installed.
  2. DIMM card
  3. System board
301, 303, 304, 305, 3XX

(301: Keyboard error.)

  1. Go to “Keyboard or Auxiliary Input Device Checkout” -siehe rechts.
  2. Keyboard
  3. External numeric keypad
  4. External keyboard
  5. Keyboard/mouse cable
  6. System board
Hardware Maintenance Manual
601, 6XX

(601: Diskette drive or controller error.)

  1. Go to “Diskette Drive Checkout” - siehe rechts.
  2. Diskette drive assembly
  3. Diskette
  4. System board
Hardware Maintenance Manual
602

(Diskette read error.)

  1. Go to “Diskette Drive Checkout” - siehe rechts.
  2. Diskette
  3. Diskette drive assembly
Hardware Maintenance Manual
604

(Unacceptable ID was read from the diskette drive.)

  1. Go to “Diskette Drive Checkout” - siehe rechts.
  2. Diskette drive assembly
  3. System board
Hardware Maintenance Manual
2402 TV Out Card
24XX

(2401: System board video error.)

System board
808X

8081: PCMCIA presence test failure. (PCMCIA revision number also checked.)
8082: PCMCIA register test failure.

  1. PC Card slot assembly
  2. PCMCIA device
  3. System board
860X

(Pointing device error when TrackPoint is disabled.)
8601: System bus error–8042 mouse interface. 8602: External mouse error.
8603: System bus error or mouse error.

  1. External mouse
  2. External keyboard
  3. System board
861X

(Pointing device error when TrackPoint is enabled.)
8611: System bus error–I/F between 8042 and IPDC.
8612: TrackPoint error.
8613: System board or TrackPoint error.

  1. Reseat the keyboard cable on the sub card.
  2. Keyboard
  3. External mouse
  4. Sub card
  5. System board
I9990301

I9990302
I9990305
I9990301: Hard disk error.
I9990302: Invalid hard disk boot record.
I9990305: No bootable device.

  1. Check that the operating system is installed in the hard disk drive. If not, install the operating system.
  2. Reseat the boot device.
  3. Check the startup sequence for the correct boot device.
  4. Check that the operating system has no failure and is installed correctly.
I9990303

(Bank–2 flash ROM check sum error.)

System board Other codes not listed above.
Go to “Undetermined Problems” - siehe rechts.

Hardware Maintenance Manual



Undokumentierte Fehlercodes

Symptom or error FRU or action, in sequence Siehe auch
00127

Nach CPU-Upgrade (Thinkpad 600, 770 etc), kann das Bios den L2-Cache der CPU nicht initialisieren

BIOS "Hack" - siehe rechts
  1. Error 127 beheben
  2. Onboard-RAM abschalten



Fehlercodes von PS/2 Computern

Diese Sammlung stammt aus dem Buch "Upgrading and Repairing PCs" und ist eine Zusammenstellung aus IBM Technical Reference Manuals und IBM Hardware Maintenance Service Manuals.

Error Code Beschreibung
 01x   Undetermined problem errors
 02x   Power supply errors
 1xx   System Board Errors
 101   System Board Error; Interrupt failure
 102   System Board Error; Timer failure
 103   System Board Error; Timer Interrupt failure
 104   System Board Error; Protected mode failure
 105   System Board Error; Last 8042 command not accepted
 106   System Board Error; Converting logic test
 107   System Board Error; Hot Non Maskable Interrupt test
 108   System Board Error; Timer bus test
 109   System Board Error; Memory select error
 110   PS/2 System Board Error; Parity check error
 111   PS/2 Memory adaptor error
 112   PS/2 MicroChannel arbitration error
 113   PS/2 MicroChannel arbitration error
 121   Unexpected hardware interrupts occured
 131   PC system board cassette port wrap test failure
 161   System Options Not Set-(Run SETUP); Dead battery
 162   System Options Not Set-(Run SETUP);
       CMOS checksum/configuration error
 163   Time & Date Not Set-(Run SETUP); Clock not updating
 164   Memory Size Error-(Run SETUP);
       CMOS setting does not match memory
 165   PS/2 System options not set
 166   PS/2 MicroChannel adapter timeout error
 199   User indicated INSTALLED DEVICES list is not correct
 2xx   Memory (RAM) errors
 201   Memory test failure, error location will be displayed
       in hexadecimal
 202   Memory address error, address lines 00-15
 203   Memory address error, address lines 16-23
 215   PS/2 Motherboard memory failure
 216   PS/2 Motherboard memory failure
 3xx   Keyboard errors
 301   Keyboard did not respond to software reset or a stuck
       key failure was detected.  If a stuck key was detected,
       the scan code for the key is displayed in hexadecimal.
 302   System Unit Keylock is Locked
 303   Keyboard or System Unit Error
 304   Keyboard or System Unit Error; Keyboard clock high
 305   PS/2 Keyboard fuse (on system board) error
 4xx   Monochrome Display Adapter (MDA) errors
 4xx   PS/2 System board parallel port errors
 401   Monochrome memory test, horizontal sync frequency test,
       or video test failure
 401   PS/2 System board parallel port failure
 408   User indicated display attributes failure
 416   User indicated character set failure
 424   User indicated 80x25 mode failure
 432   Parallel port test failure; monochrome display adapter
 5xx   Color Graphics Adapter (CGA) errors
 501   CGA memory test, horizontal sync frequency test, or video
       test failure
 508   User indicated display attribute failure
 516   User indicated character set failure
 524   User indicated 80x25 mode failure
 532   User indicated 40x25 mode failure
 540   User indicated 320x200 graphics mode failure
 548   User indicated 640x200 graphics mode failure
 6xx   Floppy drive/adapter errors
 601   Floppy drive/adapter Power On Self Test failure
 602   Drive test failure; disk boot record not valid
 606   Drive changeline function failure; drive error
 607   Disk is write protected; drive error
 608   Bad command; drive error
 610   Disk initialization failure; track 0 bad
 611   Timeout; drive error
 612   Bad Controller chip
 613   Bad Direct Memory Access; drive error
 614   Bad Direct Memory Access; boundary overrun
 615   Bad index timing; drive error
 616   Drive speed error
 621   Bad seek; drive error
 622   Bad Cyclic Redundancy Check; drive error
 623   Record not found; drive error
 624   Bad address mark; drive error
 625   Bad Controller chip; seek error
 626   Disk data compare error
 7xx   8087, 80287 or 80387 math coprocessor errors
 9xx   Parallel printer adapter errors
 901   Parallel printer adapter test failure
 10xx  Alternate parallel printer adapter errors
 1001  Alternate parallel printer adapter test failure
 11xx  Asynchronous communications adapter errors
 11xx  PS/2 System board async port errors
 1101  Asynchronous communications adapter test failure
 1102  PS/2 System board async port or serial device error
 1106  PS/2 System board async port or serial device error
 1107  PS/2 System board async port or serial cable error
 1108  PS/2 System board async port or serial device error
 1109  PS/2 System board async port or serial device error
 1112  PS/2 System board async port error
 1118  PS/2 System board async port error
 1119  PS/2 System board async port error
 12xx  Alternate asynchronous communications adapter errors
 12xx  PS/2 Dual async adapter error
 1201  Alternate asynchronous communications adapter test failure
 1202  PS/2 Dual async adapter or serial device error
 1206
 1207  PS/2 Dual async adapter or serial cable error
 1208  PS/2 Dual async adapter or serial device error
 1209
 1212  PS/2 Dual async adapter or system board error
 1218
 1219
 1227
 1233
 1234
 13xx  Game control adapter errors
 1301  Game control adapter test failure
 1301  Joy-stick test failure
 14xx  Matrix Printer errors
 15xx  Synchronous data link control (SDLC) communications
       adapter errors
 1510  8255 port B failure
 1511  8255 port A failure
 1512  8255 port C failure
 1513  8253 timer 1 did not reach terminal count
 1514  8253 timer 1 stuck on
 1515  8253 timer 0 did not reach terminal count
 1516  8253 timer 0 stuck on
 1517  8253 timer 2 did not reach terminal count
 1518  8253 timer 2 stuck on
 1519  8273 port B error
 1520  8273 port A error
 1521  8273 command/read timeout
 1522  Interrupt level 4 failure
 1523  Ring Indicate stuck on
 1524  Receive clock stuck on
 1525  Transmit clock stuck on
 1526  Test indicate stuck on
 1527  Ring indicate not on
 1528  Receive clock not on
 1529  Transmit clock not on
 1530  Test indicate not on
 1531  Data set ready not on
 1532  Carrier detect not on
 1533  Clear to send not on
 1534  Data set ready stuck on
 1536  Clear to send stuck on
 1537  Level 3 interrupt failure
 1538  Receive interrupt results error
 1539  Wrap data compare error
 1540  Direct Memory Access channel 1 error
 1541  Direct Memory Access channel 1 error
 1542  Error in 8273 error checking or status reporting
 1547  Stray interrupt level 4
 1548  Stray interrupt level 3
 1549  Interrupt presentation sequence timeout
 16xx  Display emulation errors (327x, 5520, 525x)
 17xx  Fixed disk errors
 1701  Fixed disk POST error
 1702  Fixed disk adapter error
 1703  Fixed disk drive error
 1704  Fixed disk adapter or drive error
 1780  Fixed disk 0 failure
 1781  Fixed disk 1 failure
 1782  Fixed disk controller failure
 1790  Fixed disk 0 error
 1791  Fixed disk 1 error
 18xx  I/O expansion unit errors
 1801  I/O expansion unit POST error
 1810  Enable/Disable failure
 1811  Extender card wrap test failure; disabled
 1812  High order address lines failure; disabled
 1813  Wait state failure; disabled
 1814  Enable/Disable could not be set on
 1815  Wait state failure; disabled
 1816  Extender card wrap test failure; enabled
 1817  High order address lines failure; enabled
 1818  Disable not functioning
 1819  Wait request switch not set correctly
 1820  Receiver card wrap test failure
 1821  Receiver high order address lines failure
 19xx  3270 PC attachment card errors
 20xx  Binary synchronous (BSC) adapter errors
 2010  8255 port A failure
 2011  8255 port B failure
 2012  8255 port C failure
 2013  8253 timer 1 did not reach terminal count
 2014  8253 timer 1 stuck on
 2015  8253 timer 2 did not reach terminal count or
       timer 2 stuck on
 2017  8251 Data set ready failed to come on
 2018  8251 Clear to send not sensed
 2019  8251 Data set ready stuck on
 2020  8251 Clear to send stuck on
 2021  8251 hardware reset failure
 2022  8251 software reset failure
 2023  8251 software "error reset" failure
 2024  8251 transmit ready did not come on
 2025  8251 receive ready did not come on
 2026  8251 could not force "overrun" error status
 2027  Interrupt failure; no timer interrupt
 2028  Interrupt failure; transmit, replace card or planar
 2029  Interrupt failure; transmit, replace card
 2030  Interrupt failure; receive, replace card or planar
 2031  Interrupt failure; receive, replace card
 2033  Ring indicate stuck on
 2034  Receive clock stuck on
 2035  Transmit clock stuck on
 2036  Test indicate stuck on
 2037  Ring indicate stuck on
 2038  Receive clock not on
 2039  Transmit clock not on
 2040  Test indicate not on
 2041  Data set ready not on
 2042  Carrier detect not on
 2043  Clear to send not on
 2044  Data set ready stuck on
 2045  Carrier detect stuck on
 2046  Clear to send stuck on
 2047  Unexpected transmit interrupt
 2048  Unexpected receive interrupt
 2049  Transmit data did not equal receive data
 2050  8251 detected overrun error
 2051  Lost data set ready during data wrap
 2052  Receive timeout during data wrap
 21xx  Alternate binary synchronous communications adapter errors
 2110  8255 port A failure
 2111  8255 port B failure
 2112  8255 port C failure
 2113  8253 timer 1 did not reach terminal count
 2114  8253 timer 1 stuck on
 2115  8253 timer 2 did not reach terminal count or
       timer 2 stuck on.
 2117  8251 Data set ready failed to come on
 2118  8251 Clear to send not sensed
 2119  8251 Data set ready stuck on
 2120  8251 Clear to send stuck on
 2121  8251 hardware reset failure
 2122  8251 software reset failure
 2123  8251 software "error reset" failure
 2124  8251 transmit ready did not come on
 2125  8251 receive ready did not come on
 2126  8251 could not force "overrun" error status
 2127  Interrupt failure; no timer interrupt
 2128  Interrupt failure; transmit, replace card or planar
 2129  Interrupt failure; transmit, replace card
 2130  Interrupt failure; receive, replace card or planar
 2131  Interrupt failure; receive, replace card
 2133  Ring indicate stuck on
 2134  Receive clock stuck on
 2135  Transmit clock stuck on
 2136  Test indicate stuck on
 2137  Ring indicate stuck on
 2138  Receive clock not on
 2139  Transmit clock not on
 2140  Test indicate not on
 2141  Data set ready not on
 2142  Carrier detect not on
 2143  Clear to send not on
 2144  Data set ready stuck on
 2145  Carrier detect stuck on
 2146  Clear to send stuck on
 2147  Unexpected transmit interrupt
 2148  Unexpected receive interrupt
 2149  Transmit Data did not equal receive data
 2150  8251 detected overrun error
 2151  Lost data set ready during data wrap
 2152  Receive timeout during data wrap
 22xx  Cluster adapter errors
 24xx  Enhanced Graphics Adapter (EGA) errors
 24xx  PS/2 System board Video Graphics Array (VGA) errors
 26xx  XT/370 errors
 27xx  AT/370 errors
 28xx  3278/79 emulation adapter errors
 29xx  Color/graphics printer errors
 30xx  Primary PC Network adapter error
 3001  Processor test failure
 3002  ROM checksum test failure
 3003  Unit ID PROM test failure
 3004  RAM test failure
 3005  Host Interface Controller test failure
 3006  +/- 12v test failure
 3007  Digital loopback test failure
 3008  Host detected Host Interface Controller failure
 3009  Sync failure and no Go bit
 3010  Host Interface Controller test OK and no Go bit
 3011  Go bit and no Command 41
 3012  Card not present
 3013  Digital failure; fall through
 3015  Analog failure
 3041  Hot carrier; not this card
 3042  Hot carrier; this card!
 31xx  Secondary PC Network adapter errors
 3101  Processor test failure
 3102  ROM check test failure
 3103  Unit ID PROM test failure
 3104  RAM test failure
 3105  Host Interface Controller test failure
 3106  +/- 12v test failure
 3107  Digital loopback test failure
 3108  Host detected Host Interface Controller failure
 3109  Sync failure and no Go bit
 3110  Host Interface Controller test OK and no Go bit
 3111  Go bit and no Command 41
 3112  Card not present
 3113  Digital failure; fall through
 3115  Analog failure
 3141  Hot carrier; not this card
 3142  Hot carrier; this card!
 33xx  Compact printer errors
 36xx  General Purpose Interface Bus (GPIB) adapter errors
 38xx  Data acquisition adapter errors
 39xx  Professional graphics controller errors
 71xx  Voice communications adapter errors
 73xx  3.5" external diskette drive errors
 7306  Disk changeline function failure; track 0 bad
 7307  Disk is write protected; drive error
 7308  Bad command; drive error
 7310  Disk initialization failure; track 0 bad
 7311  Timeout; drive error
 7312  Bad Controller chip
 7313  Bad Direct Memory Access; drive error
 7314  Bad Direct Memory Access; boundary overrun
 7315  Bad index timing; drive error
 7316  Drive speed error
 7321  Bad seek; drive error
 7322  Bad Cyclic Redundancy Check; drive error
 7323  Record not found; drive error
 7324  Bad address mark; drive error
 7325  Bad Controller chip; seek error
 74xx  IBM PS/2 Display adapter (VGA card) errors
 85xx  IBM Expanded Memory Adapter (XMA) errors
 86xx  PS/2 Pointing device errors
 8601  PS/2 Pointing device error
 8602  PS/2 Pointing device error
 8603  PS/2 Pointing device error or System board failure
 89xx  Music feature card errors
 100xx PS/2 Multiprotocol adapter errors
 10002 PS/2 Multiprotocol adapter or serial device error
 10006 PS/2 Multiprotocol adapter or serial device error
 10007 PS/2 Multiprotocol adapter or communications cable error
 10008 PS/2 Multiprotocol adapter or serial device error
 10009 PS/2 Multiprotocol adapter or serial device error
 10012 PS/2 Multiprotocol adapter or system board error.
 10018
 10019
 10042
 10056
 104xx PS/2 ESDI Fixed disk errors
 10480 PS/2 ESDI Fixed disk 0 failure
 10481 PS/2 ESDI Fixed disk 1 failure
 10482 PS/2 ESDI Fixed disk controller failure
 10483 PS/2 ESDI Fixed disk controller failure
 10490 PS/2 ESDI Fixed disk 0 error
 10491 PS/2 ESDI Fixed disk 1 error




Weblinks