Error Codes

Hier sind die aus den jeweiligen Hardware Maintenance Manuals fast aller ThinkPad-Generationen die Fehlercodes aufgelistet. - Zusätzlich wurden undokumentierte Fehlercodes ergänzt.

Die rechte Spalte enthält Links zur Ursachensuche und eventuelle Behebungsmöglichkeiten.

Symptom or error	FRU or action, in sequence	Siehe auch
One beep and Message CMOS Checksum error Set date and Time Press <F1> for setup	1. Replace CMOS Battery. 2. Check polarity of CMOS battery cable. 3. Check connector socket and soldering
One beep and a blank, unreadable, or flashing LCD.	1. Reseat the LCD connector. 2. LCD assembly. 3. External CRT. 4. System board.
One long and two short beeps, and a blank or unreadable LCD.	1. System board. 2. LCD assembly. 3.DIMM.	nVidia Bug bei T61/R61
Two short beeps with error codes.	POST error.	Numerische Fehler Codes
Two short beeps and a blank screen.	1. System board. 2. DIMM.	RAM-Steckplatz bei T30, R3x, X3x
Three short beeps, pause, three more short beeps, and one short beep. One short beep, pause, three short beeps, pause, three more short beeps, and one short beep. One short beep, pause, three short beeps, pause, four more short beeps, and three short beeps.	1. DIMM. 2. System board
Only the cursor appears.	Reinstall the operating system.	Fehler beim Klonen
Four cycles of four short beeps and a blank screen.	System board (security chip)
Five short beeps and a blank screen.	System board	CMOS neu flashen
Nach Einspielen eines "Custom-/Mod-BIOS"
Two cycles of five short beeps but boots then.	Security chip does not like Custom-BIOS	Disable security chip in BIOS
Undokumentiert
Three long beeps, pause, two short beeps	Wrong placed ram. Remove the CMOS battery and the RAM and insert them again or replace RAM	3 long 2 short beeps (tomsguide.com)
One short beep pause four short beeps pause one short beep pause one short beep	It does sound like a RAM-slot is bad.	1-4-1-1 (forums.lenovo.com)

Ohne Pieptöne - Symptome

Symptom or error	FRU or action, in sequence
No beep, power-on indicator on, LCD blank, and no POST.	1. Make sure that every connector is connected tightly and correctly. 2. DIMM. 3. System board.
No beep, power-on indicator on, and LCD blank during POST.	1. Reseat DIMM. 2. System board.
The power-on password prompt appears.	A power-on password or a supervisor password is set. Type the password and press Enter.
The hard-disk password prompt appears.	A hard-disk password is set. Type the password and press Enter.

Fehlermeldungen

Symptom or error	FRU or action, in sequence	Siehe auch
Device address conflict.	1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board.
Allocation error for device.	1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board.
Failing bits: nnnn.	1. DIMM. 2. System board.
Invalid system configuration data.	1. DIMM. 2. System board.
I/O device IRQ conflict.	1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board.
Operating system not found.	1. Check that the operating system has no failure and is installed correctly. 2. Enter the BIOS Setup Utility and see whether the hard disk drive and the diskette drive are properly identified. 3. Reseat the hard disk drive. 4. Reinstall the operating system. 5. Diskette drive. 6. Hard disk drive. 7. System board.
Hibernation error.	1. Restore the system configuration to what it was before the computer entered hibernation mode. 2. If memory size has been changed, re-create the hibernation file.
Fan error.	Fan.
Thermal sensing error.	System board. Fehlermeldung erscheint auch nach CPU-Upgrade z.B. bei T61	Thread im ThinkPad-Forum und T61 (Boardtausch)
Authentication of system services failed. Press <Esc> to resume.	The Predesktop Area in the HDD is corrupted. Restore it from a recovery CD
System Security - Bottom cover tamper detected und verlangt ein Passwort		Lösung: Das Kennwort wird vom System selbst gesetzt und lautet "lenovo" Durch Eingabe des Kennwort kann man das tamper detected im BIOS deaktivieren.

Numerische Fehler Codes

Errorcodes Bereich 0xxx

Error code	Symptom	FRU or action, in sequence	Siehe auch
0175	Bad CRC1, stop POST task-The EEPROM checksum is not correct.	System board	siehe 0175: Bad CRC1
0176	System Security-The system has been tampered with.	Run BIOS Setup Utility, and save the current setting by pressing F10. System board.
0177	Bad SVP data, stop POST task-The checksum of the supervisor password in the EEPROM is not correct.	System board.
0182	Bad CRC2. Enter BIOS Setup and load Setup defaults.-The checksum of the CRS2 setting in the EEPROM is not correct.	Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10. System board.
0185	Bad startup sequence settings. Enter BIOS Setup and load Setup defaults.	Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10.
0187	EAIA data access error-The access to EEPROM is failed.	System board.
0188	Invalid RFID Serialization Information Area.	System board.	Lösung
0189	Invalid RFID configuration information area-The EEPROM checksum is not correct.	System board.	Lösung
0190	Critical low-battery error.	Charge the battery pack. Battery pack.
0191	System Security-Invalid Remote Change requested.	Run BIOS Setup Utility, and then save current setting by pressing F10. System board.
0192	System Security- Embedded Security hardware tamper detected.	System board.
0199	System Security-Security password retry count exceeded.	Run BIOS Setup Utility, and then save the current setting by pressing F10. System board.
01C8	Two or more modem devices are found. Remove all but one of them. Press ESC to continue.	Remove either a Mini-PCI Card or a modem daughter card. Otherwise, press ESC to ignore the warning message. System board.
01C9	More than one Ethernet devices are found. Remove one of them. Press ESC to continue.	Remove the Ethernet device that you installed; or press ESC to ignore the warning message. System board.	1802 Error
01CA	More than one Wireless LAN devices are found. Remove one of them.	Remove the wireless LAN device that you installed. System board.
0200	Hard disk error-The hard disk is not working.	Reseat the hard disk drive. Load Setup Defaults in BIOS Setup Utility. Hard disk drive. System board.
021x	Keyboard error and two short beeps.	Run interactive tests of the keyboard and the auxiliary input device.
0220	Monitor type error-Monitor type does not match the one specified in CMOS.	Load Setup Defaults in BIOS Setup Utility.
0230	Shadow RAM error-Shadow RAM fails at offset nnnn.	System board.
0231	System RAM error-System RAM fails at offset nnnn.	DIMM. System board.
0232	Extended RAM error- Extended RAM fails at offset nnnn.	DIMM. System board.
0250	System battery error-System battery is dead.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0251	System CMOS checksum bad-Default configuration used.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0252	Password checksum bad-The password is cleared.	Reset the password by running BIOS Setup Utility.
0254	System NV7 Volume checksum bad- Default configuration used (two short beeps)	Turn off the computer and discharge CMOS. Then restart the computer.
0260	System timer error.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date. System board.
0270	Real-time clock error.	Charge the backup battery for more than 8 hours by connecting the ac adapter. Replace the backup battery and run BIOS Setup Utility to reset the time and date. System board.
0271	Date and time error-Neither the date nor the time is set in the computer.	Run BIOS Setup Utility to reset the time and date.
0280	Previous boot incomplete-Default configuration used.	Load “Setup Default” in BIOS Setup Utility. DIMM. System board.
02F0	CPU ID:xx Failed.	CPU. System board.
02F4	EISA CMOS not writable.	Load Setup Defaults in BIOS Setup Utility. Replace the backup battery. System board.
02F5	DMA test failed.	DIMM. System board.
02F6	Software NMI failed.	DIMM. System board.
02F7	Fail-safe timer NMI failed.	DIMM. System board.

Errorcodes Bereich 1xxx

Error code	Symptom	FRU or action, in sequence	Siehe auch
1802	Unauthorized network card is plugged in-Turn off and remove the miniPCI network card and two short beeps.	Remove Mini PCI network card. System board.	1802 Error
1803	Unauthorized daughter card is plugged in-Turn off and remove the daughter card.	Remove the daughter card that you installed. System board.
1804	Unauthorized WAN card is plugged in-Power off and remove the WAN card.	Remove the WAN card that you installed. System board.	1802 Error
1805	Unauthorized Wireless USB card is plugged in-Power off and remove the Wireless USB card.	Remove the Wireless USB card that you installed. System board.
1820	More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system.	Remove all but the reader that you set up for the authentication.
1830	Invalid memory configuration-Power off and install a memory module to Slot-0 or the lower slot.	Install DIMM in Slot-0, but not in Slot-1. Note: For the construction of the DIMM slot, see DIMM removal and installation - ThinkPad T400, R400.

Errorcodes Bereich 2xxx

Error code	Symptom	FRU or action, in sequence	Siehe auch
2000	Hard Drive Active Protection sensor diagnostics failed.Press ESC to continue.Press F1 to enter SETUP	Undock docking station or port replicator if it is attached to the ThinkPad Notebook. Place the ThinkPad Notebook on a horizontal surface. Do not apply any physical shock to the computer. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
2010	Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed.	Inform the following information to the customer: If in the primary bay the customer is using a non-IBM or non-Lenovo hard disk drive (HDD), or an old generation IBM HDD which is not supported by this system, with the risk in mind, the customer can still use it by pressing ESC. If in the primary drive bay the customer is using a supported IBM/Lenovo HDD with an old firmware, the customer needs to update its firmware to the latest. The latest version is available at Lenovo Support & downloads.	2010 Error
2100	Initialization error on HDD0 (Main hard disk drive)	Reseat the hard disk drive. Main hard disk drive. System board.	eine Lösungsmöglichkeit im Lenovo-Forum Sicherung F1 defekt (ThinkPad-Forum)
2101	Detection error on Main HDD (HDD0)	Reseat the M.2 solid-state drive. Replace the M.2 solid-state drive. Replace the system board.
2102	Initialization error on HDD1 (Ultrabay hard disk drive)	Reseat the hard disk drive. Ultrabay™ hard disk drive. System board.
2110	Read error on HDD0 / M.2 Main Slot (Main hard disk drive)	Reseat the hard disk / m.2 solid-state drive. Replace Main hard disk / m.2 solid-state drive. Replace System board.
2111	Read error on M.2 Main Slot (HDD0)	Reseat the hard disk / m.2 solid-state drive. Replace Main hard disk / m.2 solid-state drive. Replace System board.
2112	Read error on HDD1 (Ultrabay hard disk drive)	Reseat the hard disk drive. Ultrabay hard disk drive. System board.
2200	Machine Type and Serial Number are invalid.	Replace the system board. Seriennummer setzen	Seriennummer setzen Beachte diesen Thread
2201	Machine UUID is invalid	Replace the system board. UUID setzen	UUID setzen Beachte diesen Thread
2202	Brand Name is invalid.	Have the computer serviced.
2203	System configuration is invalid.	Have the computer serviced.
2204	System configuration data is invalid.	Have the computer serviced.

Symptome ohne Piepton

Symptom or error	FRU or action, in sequence	Siehe auch
No beep, power-on indicator on, LCD blank, and no POST.	1. Make sure that every connector is connected tightly and correctly. 2. DIMM. 3. System board.
No beep, power-on indicator on, and LCD blank during POST.	1. Reseat DIMM. 2. System board.	RAM-Steckplatz bei T30, R3x, X3x
The power-on password prompt appears.	A power-on password or a supervisor password is set. Type the password and press Enter.
The hard-disk password prompt appears.	A hard-disk password is set. Type the password and press Enter.
The DOS full screen looks smaller than it should.	Start the ThinkPad Configuration program (F1 at Boot-time) and set the Screen expansion function

LCD Symptome

Symptom or error	FRU or action, in sequence	Siehe auch
No beep, power-on indicator on, and a blank LCD during POST.	System board.
LCD backlight not working. LCD too dark. LCD brightness cannot be adjusted. LCD contrast cannot be adjusted.	1. Reseat the LCD connectors. 2. LCD assembly. 3. System board.	Sicherung für Hintergrundbeleuchtung durchgebrannt
LCD screen unreadable. Characters missing pixels. Screen abnormal. Wrong color displayed.	1. See important note for “LCD-related symptoms.”1) 2. Reseat all LCD connectors. 3. LCD assembly. 4. System board.	Flexing
Horizontal or vertical lines displayed on LCD.	LCD assembly.

¹⁾ Zitat aus dem Hardware Maintenance manual:

A bright dot means a pixel is always on (white or color.) A dark dot means a pixel is always off (black color.)

Numerische Fehlercodes (ThinkPads vor 2001)

Symptom or error	FRU or action, in sequence	Siehe auch
10X 101: Interrupt failure. 102: Timer failure. 103: Timer interrupt failure. 104: Protected mode failure. 105: Last 8042 command not accepted. 107: NMI test failure. 108: Timer bus test failure. 109: Low meg-chip select test.	System board
110 (Planar parity.)	Go to “Memory Checkout” siehe rechte Spalte DIMM card Detach the expansion unit if it is attached to the computer. System board	Hardware Maintenance Manual
111 (I/O parity.)	Go to “Memory Checkout” siehe rechte Spalte Expansion unit or port replicator. System board	Hardware Maintenance Manual
11XX 1101: Serial_A test failure.	Serial device Communication cable System board
12XX 1201: Serial_B test failure.	System board (infrared)
158 (The hard disk password was not set even though the supervisor password is set.)	Set the password for the hard disk drive.
159 (The hard disk password is not set the same as the supervisor password.)	Set the correct password for the hard disk drive.
161 (Dead battery.)	Go to “Checking the Backup Battery” 1. Backup battery System board
163 (Time and date were not set.)	Set time and date. System board
173 (Configuration data was lost.)	Select OK in the error screen; then set the time and date. Backup battery System board
174 (Configuration error: Perform “Checking the Installed Devices List” (siehe rechte Spalte) before changing any FRUs.)	Check device configuration. Hard disk drive assembly System board	Hardware Maintenance Manual
175, 177, 178 175: EEPROM CRC #1 error. 177: Supervisor password check sum error. 178: EEPROM is not functional.	System board
17XX 1701: Hard disk controller failure. 1780, 1790: Hard disk 0 error. 1781, 1791: Hard disk 1 error.	Hard disk drive System board
183 (Incorrect password entered at the supervisor password prompt.)	Have the user examine the password.
184 (Power-on password check sum error.)	Reset the power-on password in Easy-Setup.
185 (The startup sequence is not valid. Suspect that power was off when the startup sequence was being updated.)	Reset the startup sequence in Easy-Setup.
186	System board
188, 189 (BAD EEPROM CRC #1. An incorrect checksum of the EEPROM is received.)	System board
190 (A depleted battery pack was installed when the power was on.)	Go to “Checking the Battery Pack” in Hardware Maintenance Manual.	Hardware Maintenance Manual
191XX (PM initialization error.)	System board
192 (Fan error.)	Measure the voltage of the backup battery. If the voltage is not correct, replace the backup battery. Fan System board
193 (RF Antenna has been removed.)	Type the correct Supervisor Password at the password prompt. Reseat the RF Antenna to the HDD cover.
194 (The computer is carried through the portal gate.)	Type the correct Supervisor Password at the password prompt.
195 (The configuration read from the hibernation area does not match the actual configuration.)	Check if the configuration was changed. For example, check if the DIMM card is added.
196 (A read error occurred in the hibernation area of the hard disk drive.)	Run the hard disk drive test. Hard disk drive
199XX (Resume error.)	System board
1XX	System board
2XX 201: Memory data error. 202: Memory line error 00–15. 203: Memory line error 16–23. 205: Memory test failure on on-board memory. 221: ROM to RAM remap error.	Go to “Memory Checkout” - siehe rechts. DIMM card System board	201: leere BIOS-Batterie, z.B. bei 701 Hardware Maintenance Manual
225 (Unsupported memory module.)	Check if the supported DIMM is installed. DIMM card System board
301, 303, 304, 305, 3XX (301: Keyboard error.)	Go to “Keyboard or Auxiliary Input Device Checkout” -siehe rechts. Keyboard External numeric keypad External keyboard Keyboard/mouse cable System board	Hardware Maintenance Manual
601, 6XX (601: Diskette drive or controller error.)	Go to “Diskette Drive Checkout” - siehe rechts. Diskette drive assembly Diskette System board	Hardware Maintenance Manual
602 (Diskette read error.)	Go to “Diskette Drive Checkout” - siehe rechts. Diskette Diskette drive assembly	Hardware Maintenance Manual
604 (Unacceptable ID was read from the diskette drive.)	Go to “Diskette Drive Checkout” - siehe rechts. Diskette drive assembly System board	Hardware Maintenance Manual
2402	TV Out Card
24XX (2401: System board video error.)	System board
808X 8081: PCMCIA presence test failure. (PCMCIA revision number also checked.) 8082: PCMCIA register test failure.	PC Card slot assembly PCMCIA device System board
860X (Pointing device error when TrackPoint is disabled.) 8601: System bus error–8042 mouse interface. 8602: External mouse error. 8603: System bus error or mouse error.	External mouse External keyboard System board
861X (Pointing device error when TrackPoint is enabled.) 8611: System bus error–I/F between 8042 and IPDC. 8612: TrackPoint error. 8613: System board or TrackPoint error.	Reseat the keyboard cable on the sub card. Keyboard External mouse Sub card System board
I9990301 I9990302 I9990305 I9990301: Hard disk error. I9990302: Invalid hard disk boot record. I9990305: No bootable device.	Check that the operating system is installed in the hard disk drive. If not, install the operating system. Reseat the boot device. Check the startup sequence for the correct boot device. Check that the operating system has no failure and is installed correctly.
I9990303 (Bank–2 flash ROM check sum error.)	System board Other codes not listed above. Go to “Undetermined Problems” - siehe rechts.	Hardware Maintenance Manual

Aus dem Hardware Maintenance Manual eines 370C:

If an error is detected by the diagnostic tests, a four-digit FRU code is displayed. The FRU code indicates two suspected FRUs. Replace the FRU that is indicated by the two leftmost digits first, then replace the FRU indicated by the two rightmost digits. No FRU is assigned to code 00. If only one FRU is suspected, the other FRU code is filled with zeros. See the referenced page before replacing the FRU. Beispiel:

Wird bei der Diagnose "FRU 2010" angezeigt, bedeutet nach der u.a. Tabelle die "20" den Memory und die "10" das System Board.

FRU-Tabelle

FRU-Code	FRU/Tätigkeit
10	System Board
11	Processor Card (370C, 750Ce, 755C, and 755Cs)
15	Audio Card
20	Memory (See “Memory Checkout” on page 201.)
30	Reserved
32	External Keyboard
33	External Mouse
40	LCD Assembly (See “Digitizer Adjustment” on page 205 and important note for “LCD Related Symptoms” on page 223.)
45	External CRT
50	1. Reseat the Drive (FDD-1) 2. Diskette Drive (FDD-1)
51	1. Reseat the Drive (FDD-2) 2. Diskette Drive (FDD-2)
60	1. Reseat the Hard Disk Drive (HDD-1) 2. Hard Disk Drive (HDD-1)
61	1. Reseat the Hard Disk Drive (HDD-2) 2. Hard Disk Drive (HDD-2)
70	PCMCIA-2 (Replicator)
80	Cellular Modem (370C, 750Ce, 755C, and 755Cs)
81	Internal Modem Card
90	-

Zitat aus Hardware Maintenance Manual:

Note: The device ID and error codes are used to indicate the detail portion of the FRU which caused the error. If replacing a FRU does not correct a problem, see the Device ID or error code from the previous failure. If they have changed, the cause might be because the new FRU is defective or that the FRU was incorrectly installed. If the problem remains after replacement of the FRUs, go to “Undetermined Problems” on page 227.

Undokumentierte Fehlercodes

Symptom or error	FRU or action, in sequence	Siehe auch
00127 Nach CPU-Upgrade (Thinkpad 600, 770 etc), kann das Bios den L2-Cache der CPU nicht initialisieren	BIOS "Hack" - siehe rechts	Error 127 beheben Onboard-RAM abschalten

Fehlercodes von PS/2 Computern

Diese Sammlung stammt aus dem Buch "Upgrading and Repairing PCs" und ist eine Zusammenstellung aus IBM Technical Reference Manuals und IBM Hardware Maintenance Service Manuals.

Error Code Beschreibung

01x Undetermined problem errors 02x Power supply errors 1xx System Board Errors 101 System Board Error; Interrupt failure 102 System Board Error; Timer failure 103 System Board Error; Timer Interrupt failure 104 System Board Error; Protected mode failure 105 System Board Error; Last 8042 command not accepted 106 System Board Error; Converting logic test 107 System Board Error; Hot Non Maskable Interrupt test 108 System Board Error; Timer bus test 109 System Board Error; Memory select error 110 PS/2 System Board Error; Parity check error 111 PS/2 Memory adaptor error 112 PS/2 MicroChannel arbitration error 113 PS/2 MicroChannel arbitration error 121 Unexpected hardware interrupts occured 131 PC system board cassette port wrap test failure 161 System Options Not Set-(Run SETUP); Dead battery 162 System Options Not Set-(Run SETUP); CMOS checksum/configuration error 163 Time & Date Not Set-(Run SETUP); Clock not updating 164 Memory Size Error-(Run SETUP); CMOS setting does not match memory 165 PS/2 System options not set 166 PS/2 MicroChannel adapter timeout error 199 User indicated INSTALLED DEVICES list is not correct 2xx Memory (RAM) errors 201 Memory test failure, error location will be displayed in hexadecimal 202 Memory address error, address lines 00-15 203 Memory address error, address lines 16-23 215 PS/2 Motherboard memory failure 216 PS/2 Motherboard memory failure 3xx Keyboard errors 301 Keyboard did not respond to software reset or a stuck key failure was detected. If a stuck key was detected, the scan code for the key is displayed in hexadecimal. 302 System Unit Keylock is Locked 303 Keyboard or System Unit Error 304 Keyboard or System Unit Error; Keyboard clock high 305 PS/2 Keyboard fuse (on system board) error 4xx Monochrome Display Adapter (MDA) errors 4xx PS/2 System board parallel port errors 401 Monochrome memory test, horizontal sync frequency test, or video test failure 401 PS/2 System board parallel port failure 408 User indicated display attributes failure 416 User indicated character set failure 424 User indicated 80x25 mode failure 432 Parallel port test failure; monochrome display adapter 5xx Color Graphics Adapter (CGA) errors 501 CGA memory test, horizontal sync frequency test, or video test failure 508 User indicated display attribute failure 516 User indicated character set failure 524 User indicated 80x25 mode failure 532 User indicated 40x25 mode failure 540 User indicated 320x200 graphics mode failure 548 User indicated 640x200 graphics mode failure 6xx Floppy drive/adapter errors 601 Floppy drive/adapter Power On Self Test failure 602 Drive test failure; disk boot record not valid 606 Drive changeline function failure; drive error 607 Disk is write protected; drive error 608 Bad command; drive error 610 Disk initialization failure; track 0 bad 611 Timeout; drive error 612 Bad Controller chip 613 Bad Direct Memory Access; drive error 614 Bad Direct Memory Access; boundary overrun 615 Bad index timing; drive error 616 Drive speed error 621 Bad seek; drive error 622 Bad Cyclic Redundancy Check; drive error 623 Record not found; drive error 624 Bad address mark; drive error 625 Bad Controller chip; seek error 626 Disk data compare error 7xx 8087, 80287 or 80387 math coprocessor errors 9xx Parallel printer adapter errors 901 Parallel printer adapter test failure 10xx Alternate parallel printer adapter errors 1001 Alternate parallel printer adapter test failure 11xx Asynchronous communications adapter errors 11xx PS/2 System board async port errors 1101 Asynchronous communications adapter test failure 1102 PS/2 System board async port or serial device error 1106 PS/2 System board async port or serial device error 1107 PS/2 System board async port or serial cable error 1108 PS/2 System board async port or serial device error 1109 PS/2 System board async port or serial device error 1112 PS/2 System board async port error 1118 PS/2 System board async port error 1119 PS/2 System board async port error 12xx Alternate asynchronous communications adapter errors 12xx PS/2 Dual async adapter error 1201 Alternate asynchronous communications adapter test failure 1202 PS/2 Dual async adapter or serial device error 1206 1207 PS/2 Dual async adapter or serial cable error 1208 PS/2 Dual async adapter or serial device error 1209 1212 PS/2 Dual async adapter or system board error 1218 1219 1227 1233 1234 13xx Game control adapter errors 1301 Game control adapter test failure 1301 Joy-stick test failure 14xx Matrix Printer errors 15xx Synchronous data link control (SDLC) communications adapter errors 1510 8255 port B failure 1511 8255 port A failure 1512 8255 port C failure 1513 8253 timer 1 did not reach terminal count 1514 8253 timer 1 stuck on 1515 8253 timer 0 did not reach terminal count 1516 8253 timer 0 stuck on 1517 8253 timer 2 did not reach terminal count 1518 8253 timer 2 stuck on 1519 8273 port B error 1520 8273 port A error 1521 8273 command/read timeout 1522 Interrupt level 4 failure 1523 Ring Indicate stuck on 1524 Receive clock stuck on 1525 Transmit clock stuck on 1526 Test indicate stuck on 1527 Ring indicate not on 1528 Receive clock not on 1529 Transmit clock not on 1530 Test indicate not on 1531 Data set ready not on 1532 Carrier detect not on 1533 Clear to send not on 1534 Data set ready stuck on 1536 Clear to send stuck on 1537 Level 3 interrupt failure 1538 Receive interrupt results error 1539 Wrap data compare error 1540 Direct Memory Access channel 1 error 1541 Direct Memory Access channel 1 error 1542 Error in 8273 error checking or status reporting 1547 Stray interrupt level 4 1548 Stray interrupt level 3 1549 Interrupt presentation sequence timeout 16xx Display emulation errors (327x, 5520, 525x) 17xx Fixed disk errors 1701 Fixed disk POST error 1702 Fixed disk adapter error 1703 Fixed disk drive error 1704 Fixed disk adapter or drive error 1780 Fixed disk 0 failure 1781 Fixed disk 1 failure 1782 Fixed disk controller failure 1790 Fixed disk 0 error 1791 Fixed disk 1 error 18xx I/O expansion unit errors 1801 I/O expansion unit POST error 1810 Enable/Disable failure 1811 Extender card wrap test failure; disabled 1812 High order address lines failure; disabled 1813 Wait state failure; disabled 1814 Enable/Disable could not be set on 1815 Wait state failure; disabled 1816 Extender card wrap test failure; enabled 1817 High order address lines failure; enabled 1818 Disable not functioning 1819 Wait request switch not set correctly 1820 Receiver card wrap test failure 1821 Receiver high order address lines failure 19xx 3270 PC attachment card errors 20xx Binary synchronous (BSC) adapter errors 2010 8255 port A failure 2011 8255 port B failure 2012 8255 port C failure 2013 8253 timer 1 did not reach terminal count 2014 8253 timer 1 stuck on 2015 8253 timer 2 did not reach terminal count or timer 2 stuck on 2017 8251 Data set ready failed to come on 2018 8251 Clear to send not sensed 2019 8251 Data set ready stuck on 2020 8251 Clear to send stuck on 2021 8251 hardware reset failure 2022 8251 software reset failure 2023 8251 software "error reset" failure 2024 8251 transmit ready did not come on 2025 8251 receive ready did not come on 2026 8251 could not force "overrun" error status 2027 Interrupt failure; no timer interrupt 2028 Interrupt failure; transmit, replace card or planar 2029 Interrupt failure; transmit, replace card 2030 Interrupt failure; receive, replace card or planar 2031 Interrupt failure; receive, replace card 2033 Ring indicate stuck on 2034 Receive clock stuck on 2035 Transmit clock stuck on 2036 Test indicate stuck on 2037 Ring indicate stuck on 2038 Receive clock not on 2039 Transmit clock not on 2040 Test indicate not on 2041 Data set ready not on 2042 Carrier detect not on 2043 Clear to send not on 2044 Data set ready stuck on 2045 Carrier detect stuck on 2046 Clear to send stuck on 2047 Unexpected transmit interrupt 2048 Unexpected receive interrupt 2049 Transmit data did not equal receive data 2050 8251 detected overrun error 2051 Lost data set ready during data wrap 2052 Receive timeout during data wrap 21xx Alternate binary synchronous communications adapter errors 2110 8255 port A failure 2111 8255 port B failure 2112 8255 port C failure 2113 8253 timer 1 did not reach terminal count 2114 8253 timer 1 stuck on 2115 8253 timer 2 did not reach terminal count or timer 2 stuck on. 2117 8251 Data set ready failed to come on 2118 8251 Clear to send not sensed 2119 8251 Data set ready stuck on 2120 8251 Clear to send stuck on 2121 8251 hardware reset failure 2122 8251 software reset failure 2123 8251 software "error reset" failure 2124 8251 transmit ready did not come on 2125 8251 receive ready did not come on 2126 8251 could not force "overrun" error status 2127 Interrupt failure; no timer interrupt 2128 Interrupt failure; transmit, replace card or planar 2129 Interrupt failure; transmit, replace card 2130 Interrupt failure; receive, replace card or planar 2131 Interrupt failure; receive, replace card 2133 Ring indicate stuck on 2134 Receive clock stuck on 2135 Transmit clock stuck on 2136 Test indicate stuck on 2137 Ring indicate stuck on 2138 Receive clock not on 2139 Transmit clock not on 2140 Test indicate not on 2141 Data set ready not on 2142 Carrier detect not on 2143 Clear to send not on 2144 Data set ready stuck on 2145 Carrier detect stuck on 2146 Clear to send stuck on 2147 Unexpected transmit interrupt 2148 Unexpected receive interrupt 2149 Transmit Data did not equal receive data 2150 8251 detected overrun error 2151 Lost data set ready during data wrap 2152 Receive timeout during data wrap 22xx Cluster adapter errors 24xx Enhanced Graphics Adapter (EGA) errors 24xx PS/2 System board Video Graphics Array (VGA) errors 26xx XT/370 errors 27xx AT/370 errors 28xx 3278/79 emulation adapter errors 29xx Color/graphics printer errors 30xx Primary PC Network adapter error 3001 Processor test failure 3002 ROM checksum test failure 3003 Unit ID PROM test failure 3004 RAM test failure 3005 Host Interface Controller test failure 3006 +/- 12v test failure 3007 Digital loopback test failure 3008 Host detected Host Interface Controller failure 3009 Sync failure and no Go bit 3010 Host Interface Controller test OK and no Go bit 3011 Go bit and no Command 41 3012 Card not present 3013 Digital failure; fall through 3015 Analog failure 3041 Hot carrier; not this card 3042 Hot carrier; this card! 31xx Secondary PC Network adapter errors 3101 Processor test failure 3102 ROM check test failure 3103 Unit ID PROM test failure 3104 RAM test failure 3105 Host Interface Controller test failure 3106 +/- 12v test failure 3107 Digital loopback test failure 3108 Host detected Host Interface Controller failure 3109 Sync failure and no Go bit 3110 Host Interface Controller test OK and no Go bit 3111 Go bit and no Command 41 3112 Card not present 3113 Digital failure; fall through 3115 Analog failure 3141 Hot carrier; not this card 3142 Hot carrier; this card! 33xx Compact printer errors 36xx General Purpose Interface Bus (GPIB) adapter errors 38xx Data acquisition adapter errors 39xx Professional graphics controller errors 71xx Voice communications adapter errors 73xx 3.5" external diskette drive errors 7306 Disk changeline function failure; track 0 bad 7307 Disk is write protected; drive error 7308 Bad command; drive error 7310 Disk initialization failure; track 0 bad 7311 Timeout; drive error 7312 Bad Controller chip 7313 Bad Direct Memory Access; drive error 7314 Bad Direct Memory Access; boundary overrun 7315 Bad index timing; drive error 7316 Drive speed error 7321 Bad seek; drive error 7322 Bad Cyclic Redundancy Check; drive error 7323 Record not found; drive error 7324 Bad address mark; drive error 7325 Bad Controller chip; seek error 74xx IBM PS/2 Display adapter (VGA card) errors 85xx IBM Expanded Memory Adapter (XMA) errors 86xx PS/2 Pointing device errors 8601 PS/2 Pointing device error 8602 PS/2 Pointing device error 8603 PS/2 Pointing device error or System board failure 89xx Music feature card errors 100xx PS/2 Multiprotocol adapter errors 10002 PS/2 Multiprotocol adapter or serial device error 10006 PS/2 Multiprotocol adapter or serial device error 10007 PS/2 Multiprotocol adapter or communications cable error 10008 PS/2 Multiprotocol adapter or serial device error 10009 PS/2 Multiprotocol adapter or serial device error 10012 PS/2 Multiprotocol adapter or system board error. 10018 10019 10042 10056 104xx PS/2 ESDI Fixed disk errors 10480 PS/2 ESDI Fixed disk 0 failure 10481 PS/2 ESDI Fixed disk 1 failure 10482 PS/2 ESDI Fixed disk controller failure 10483 PS/2 ESDI Fixed disk controller failure 10490 PS/2 ESDI Fixed disk 0 error 10491 PS/2 ESDI Fixed disk 1 error

Weblinks

• siehe auch Wiki-Artikel Fehlersuche bei ThinkPads
• Numeric error codes - ThinkPad R400, T400
• Numeric error codes - ThinkPad 770
• Beep and no beep symptoms - ThinkPad 560X
• Beep and no beep symptoms - ThinkPad General
• Beep and No beep symptoms - ThinkPad R500
• Phoenix BIOS beep codes
• FRU-Codes am Beispiel ThinkPad 560x